background image

Multi Gas Clip Simple Plus User’s Manual

UM MGC-S-PLUS v1.00a 

Portable gas detectors you can count on

1 of 18

WARNING STATEMENTS/AVERTISSEEMENT

 Do not substitute components as this may interfere with the intrinsic safety of the device .
 Ne remplacez pas les composants car cela pourrait interférer avec la sécurité intrinsèque de l’appareil .
 DO NOT substitute any other battery type than specified and supplied by Gas Clip Technologies . 
 Only use Gas Clip Technologies parts in the detector . Non-approved parts will void the warranty and are 

considered unsafe .

 Before each use, check that all sensor and alarm ports are clear of any obstructions, i .e . debris or blockage .
 The detector contains a lithium battery that must be disposed of by a qualified recycler . Check local regulations for 

proper disposal .

 DO NOT use IR communications when an explosive atmosphere may be present .
 If you suspect any malfunction or have any technical problems, contact GCT at 1-877-525-0808 .
 The battery may present a fire or chemical burn hazard if mistreated . Do not disassemble, heat above 100°C 

(212°F) or incinerate . Contact Gas Clip Technologies for replacement instructions . Use of another battery may 
present a risk of fire or explosion . 

 Keep new and used batteries away from children .
 Do not expose the detector to sensor poisons such as, but not limited to, alcohol and citrus based products .  

Exposure to poisons may impair the accuracy and/or response time of the detector .

 If suspected sensor poisoning has occurred, recheck the detector (both calibrate and bump test) .
 Caution: Before each day’s usage, sensitivity must be tested on a known concentration of methane equivalent 

to 25-50% of full-scale concentration . Accuracy must be within 0-20% of actual . Accuracy may be corrected by 
calibrating the detector . 

 Any rapid up-scale reading, followed by a declining or erratic reading, may indicate a gas concentration beyond 

upper scale limit which may be hazardous .

 Toute rapide haut de gamme lecture suivie d'une lecture erratique baisse ou peut indiquer une concentration de 

gaz supérieure à la limite superieure de l'échelle qui peut être dangereux .

 Strong Electromagnetic Interference (EMI) may cause incorrect operations .
 Only the combustible gas detection portion of this instrument has been assessed for performance by CSA 

International .

 READ FIRST BEFORE OPERATION

Gas Clip Technologies (GCT) Multi Gas Clip Simple Plus (MGC-S-PLUS) detectors are personal safety devices designed to 
detect the presence of specific toxic gases: carbon monoxide (CO), hydrogen sulfide (H

2

S), oxygen (O

2

) and combustible 

gases/Lower Explosive Limit (LEL) . Before operation, ensure that you have been properly trained on the use of the 
equipment and the appropriate actions to take in the event of an alarm condition . 

Summary of Contents for Multi Gas Clip Simple Plus





















Reviews: