background image

 

9

be unable to power the 2

nd

, 3

rd

 and 4

th

 

docks in the series.  There are two 
options in this case.  The first option is 
to connect each dock to a suitable 
power source using the wall cube power 
supply that was included with the IQ 
Express Dock.  A suitable, grounded 
power strip may be used.  The second 
option is to purchase the optional power 
supply that is capable of running up to 
four IQ Express Docks from a single 

electrical outlet. 

 

Figure 2.6.2 Preferred Method for USB 

Connection and Powering Multiple IQ 

Express Docks. 

Under no circumstances can multiple IQ 
Express Docks be run from a single USB 

port without supplemental power. 

2.7  Connecting the Calibration 

Gas Cylinder(s) to the 
Dock(s) 

Connection requirements for calibration gas 
cylinders vary with how many docks will be 
connected to the cylinder and whether the 
calibration gas is considered reactive.  
Enhanced versions of the IQ Express 
include a tubing assembly that is suitable for 
use with reactive gases.  

 

Figure 2.7. IQ Express Gas Ports 

For instructions on connecting the gas 
cylinder to a single IQ Express dock 

proceed to section 2.7.1. 
For instructions on connecting the gas 
cylinder to multiple IQ Express docks 

proceed to section 2.7.2. 

2.7.1  Single Cylinder to Single IQ 

Express Dock 

1.  Insert the demand flow regulator into the 

calibration gas cylinder. 

2.  Standard docks are delivered with a 24” 

piece of tubing with a white quick 
disconnect on one end.  Enhanced 
docks are delivered with a 24” piece of 
tubing that meets a black elbow fitting 
followed by a 1” piece of standard 
tubing.  Slide the open end of the tubing 
assembly over the regulator.  For 
enhanced docks, slide the open end of 
the 1” piece of tubing over the regulator. 

 

Figure 2.7.1 Standard versus Enhanced 

Setup for Regulator and Tubing 

Summary of Contents for IQ Express





























Reviews: