background image

www.gastron.com

32

_

33

GTC-550

Instruction Manual

6.4.7. Maintenance Mode

- It is a mode that displays value converted from processor after inputting 20mA current to (mA) 

terminal.

- Press "FUNC" S/W when the displayed number is stable to display SUC (Success) for a current 

input within normal range and move to the next item.

- C-F (Calibration-Fail) displays when a current out of range is inputted. After confirming input 

current after re-display of current value then press "FUNC" S/W again to confirm.

- When "RESET" S/W is pressed, it returns to gas concentration display mode.

- When "oUt" is selected, it is a mode after input current, which sets 4 mA output current.

(Default 4.00)

- Connect ammeter to 4~20 mA output terminal and press "UP" S/W or "DOWN" S/W to match the 

values on ammeter and FND then press "FUNC" S/W to set output current and move to the next 

item.

- When "RESET" S/W is pressed, it returns to gas concentration display mode.

- Mode that sets 20 mA output current. (Default 20.00)
- Due to display limit of FND, 10-digit and decimal point digit flashes in 0.5 sec interval.

- Connect ammeter to 4~20 mA output terminal and press "UP" S/W or "DOWN" S/W to match the 

values on ammeter and FND then press "FUNC" S/W to set output current and move to the next 

item.

- When "RESET" S/W is pressed, it returns to gas concentration display mode.

▼ ▲

■ Pressing both "RESET" and "TEST" S/W for 2 sec or longer in gas concentration display mode enters 

  Maintenance mode.

■ "RESET" S/W must be pressed in Maintenance mode to return to gas concentration display mode.

- Mode that selects function to set current input and output values that are reference of Channel 

unit. Pressing "UP" S/W or "DOWN" S/W displays "In" or "oUt", respectively.

- When a desired mode is displayed, press "FUNC" S/W to set it and enter the mode.
- When "In" is selected, mode sets current input. When "oUt" is selected, mode sets current 

output.

- When "RESET" S/W is pressed, it returns to gas concentration display mode.

- It is when "In" is selected and a mode that sets by inputting 4 mA current.
- Press "FUNC" S/W to enter function that displays current input by number.
- When "RESET" S/W is pressed, it returns to gas concentration display mode.

- It is a mode that displays value converted from processor after inputting 4mA current to (mA) 

terminal.

- Press "FUNC" S/W when the displayed number is stable to display SUC (Success) for a current 

input within normal range and move to the next item.

- C-F (Calibration-Fail) displays when a current out of range is inputted. After confirming input 

current after re-display of current value then press "FUNC" S/W again to confirm.

- When "RESET" S/W is pressed, it returns to gas concentration display mode.

- Mode that sets by inputting 20 mA current.

- Press "FUNC" S/W to enter function that displays current input by number.
- When "RESET" S/W is pressed, it returns to gas concentration display mode.

OR

OR

▼ ▲

6. Operation Method

6. Operation Method

Summary of Contents for GTC-550





















Reviews: