background image

www.gastron.com

34

_

35

GTD-3000TxW

Instruction Manual

11. Precautions before Installation

■ Relative Humidity: 5% ~ 99% (Non-condensing)

■ Installation Site: Indoor and Outdoor

■ Explosion Ignition Group for Target Gas or Vapor: Ex d IIC T6

■ 

During wiring work, use explosion-proof cable gland at cable inlet or tightly seal cable conduit during metal cable wiring  

  construction to prevent spread of flames in case of explosion or movement of gas, etc. through the cable conduit within 

   50 mm. All materials including materials used for sealing of unused inlets must have safety certificates!

■ When connecting the equipment with cable, screw thread must be tightened 5 threads or more.

■ Work in conditions satisfying other [Standards for Selection, Installation, and Maintenance, etc. of Explosion-proof Electric  

  Machine and Equipment Wiring, etc. at Work Site]

12. Revision History

[Figure 17. High-Pressure Packing Type]

[Figure 18. Y Sealing Compound]

Cable

Cable

Inside

Inside

Outside

Outside

Lead-in unit connector

Lead-in unit connector

Charging compound

Cable-fixing device

 Pipe for piping

Cable-fixing device

Sealing ring

Sealing

ring

Connector

Pipe for piping

Compressed

element

Connector for fixing 

compressed element

VERSION

CONTENTS

DATE

0.1

* Manual Initial Revision

2017. 09. 29

0.2

* Correct typos and typographical errors

2019. 11. 19

Summary of Contents for GTD-3000Tx



















Reviews: