background image

Venice Single Board Computer Operating Manual

2. CONNECTORS

The board interface connector pin assignments and signal descriptions are included in
the following sections. The connectors are listed in the table below.

Connector Populated

Function

J1

Yes

Micro SD / Nano SIM Socket

J2

Yes

Coin Cell Battery Socket

J3

Yes

Serial Peripheral Interface (SPI)

J4

Yes

MIPI CSI and DSI Header

J5

Yes

Peripheral Expansion (GPIO, UART, I2C, ADC)

J6

Yes

SOM Connector

J7

No

Test Header

J8

Yes

Mini-PCIe Socket with PCIe and USB 2.0

J9

Yes

SOM Connector

J10

Yes

Mini-PCIe Socket with PCIe and USB 2.0 and SIM

J11

Yes

RS232/RS485 Serial Ports

J12

Yes

5V Fan Speed Control

J13

Yes

Tamper Switch

J14

No

Optional GPS Receiver MMCX Antenna

J15

No

Optional Power Input Header

J16

Yes

Input Power Barrel Jack

J17

Yes

Gigabit Ethernet Ports and Active/Passive PoE Input

Power

J18

No

Optional USB Host Type A Socket

J19

Yes

USB OTG Micro B Socket

J20

No

Optional Push Button Switch Header

Connector Summary

Micro-SD Flash and Cellular Nano SIM Expansion Socket (J1)

Flash expansion is possible by installing an industry standard 11mm by 15mm Flash
card into the socket. The Micro-SD Flash card cannot be installed or removed with
power applied to the SBC. The Micro-SD and Nano SIM sockets are combined. The
command signal is routed to the processor.by default. The Nano SIM socket is routed to
Mini-PCIe socket J10.

Battery Coin Cell Socket (J2)

The 12.5mm backup battery socket allows for easy replacement of the battery. A
standard 12.5mm, BR1225, 3V, 50mAH Lithium coin cell should be used when replacing
the battery. Replacement batteries can be ordered from Digi-Key with part number
P183-ND.

Serial Peripheral Interface (SPI) Expansion (J3)

An SPI port is available through a 6-pin header in a 1x6 configuration with 2mm
spacing. The mating connector is a JST PAP-06V-S, available from Digi-Key as
part number 455-1490-ND. The mating connector pins are JST SPHD-002T-P05,
available from Digi-Key as part number 455-1313-1-ND.

GATEWORKS.COM                            3026 S. Higuera St San Luis Obispo, CA 93401

P:(805)781-2000

18 of 32

Summary of Contents for Venice GW720

































Reviews: