background image

P.24

請維持良好習慣: 颶風255電動遙控直升機為高科技精密零組件構成之休閒用品,玩家請時常注意確保機體的保養及維持
機構組件之性能,於飛行時展現其優異的性能,不當的保養維護,會導致飛行時的安全度降低。

主旋翼運轉發生異常時,請檢查主旋翼、橫軸;主軸是否有變形或平衡不良,必要時請更新異常機構零件。

飛行時不慎觸地,請優先檢查旋翼頭零件及橫軸螺絲、混控臂、平衡桿等。

雙槳平衡:請檢查連桿長度是否平均及雙槳的配重須一致。

皮帶:長期運轉會使皮帶造成老化、斷齒等狀況為了維護飛行安全請更換新品。

停旋:主旋翼轉速偏低,請注意主旋翼的PITCH是否偏高或停旋點油門曲線過低。

陀螺儀感度:停旋時陀螺儀朝某一方偏移,或撥方向舵柄回復到中立點時,尾翼產生延遲,無法停頓在控制點上,請增加陀螺儀感度。

陀螺儀感度:停旋或全油門時尾翼左右來回搖擺,請降低陀螺儀感度。

停旋:主旋翼轉速偏高,請注意主旋翼的PITCH是否偏低或停旋點油門曲線過高。

主軸軸承:主軸軸承經長期負載運作,正常飛行約100趟後必須檢查各部機構、軸承性能狀況,
如有異常請更換新品以保持運作順暢。

如經常進行3D飛行或嚴重撞擊,建議你必須時常檢查機構、零件、軸承等,如發現異常狀態或間隙、異音或是轉動
有明顯干涉等都必須更換新品。

單向軸承飛行50趟後請卸下來清潔與重新上油。

The Hurricane 255 heli product is not a toy, for the consideration of safety and performance, it is necessary to check 
and maintain after each flight.

When spinning, if the blades are unbalanced or the tracking of both blades is not even with each other, Check or 
replace the Blades / Mast / spindle shaft to fix the problem. 

Check the mechanism and bearings after 100 normal flights for safety. 

Check and replace the damaged parts after crash of hard 3D flight.

When hovering, decrease the collective pitch or adjust the hovering throttle curve higher if the head speed is too 
slow, increase the collective pitch or adjust the hovering throttle curve lower if the head speed is too high.

Check the Rotor head assembly / main grip screws / mixing arms / flybar after crash (even in slightly compact), 
replace the damaged parts before next flight.

Make sure the length of each linkage should be adjust properly and the blade should be balanced.

Remove the one way bearing after 50 flights, clean it and grease it with oil. 

Replace the belt if there is any fissure on it.

Increase the gyro gain if the tail is drifting to one side when hovering.

Decrease the gyro gain if the tail wags in hovering.

Maintenance

維修檢查事項

Summary of Contents for Hurricane 255





























Reviews: