P.5
請先將4號(
P1.4X2X3
)置入剪型
臂內再將拉桿合上後再依序鎖上。
I n s t a l l t h e s p a c e r ( P 1 . 4 X 2 X 3 )
b e f o r e a s s e m b l e t h e l i n k a g e .
CNC Swashplate
Assembly
CNC十字盤組
CNC Washout Base &
Arms Assembly
CNC剪形臂及相位器組
粗牙螺絲
Self taping screws
公制螺絲
Machine Screw
公制螺絲
Machine Screw
軸承
華司
Bearing
Washer
公制螺絲
Machine Screw
軸承
Bearing
柱狀體
Tube
柱狀體
Tube
Metal Balls with Stand
(3.5mm)
金屬球頭組3.5mm(長)
Ø1.4X6
M1.4X5
B1.5X4X1.35
P1.4X2X3
#203643
#883503
W1.4X2.5X0.4
B8X12X2.5
#203641
M1.4X6
M1.4X15
P1.4X2X9
Use the thread-lock adhesive on the
tip of screw for 1mm width.
螺絲止鬆劑上膠位置約為螺紋前端
1mm寬度。
IMPORTANT
Use the thread-lock adhesive if the
screws are tightened to the metal parts.
請注意
組裝時如遇螺絲鎖於金屬件,請適量
使用 螺絲止鬆劑 以確保飛行安全!
Use the thread-lock adhesive on the
tip of screw for 1mm width.
螺絲止鬆劑上膠位置約為螺紋前端
1mm寬度。
IMPORTANT
Use the thread-lock adhesive if the
screws are tightened to the metal parts.
請注意
組裝時如遇螺絲鎖於金屬件,請適量
使用 螺絲止鬆劑 以確保飛行安全!
組裝注 意事項:
零件組 裝時請依說明書指示上 膠,並適度控制 螺絲起子的扭力,以避免螺絲 或 零 件
滑牙造 成損壞,在裝配原廠已 完成組裝之零件 時,請再確認各螺絲是否確實 鎖 緊 上膠 。
N o t e o f A s s e m b l i n g :
D o n o t t i g h t e n t h e s c r e w s t o o m u c h t h a t b r e a k t h e t h r e a d o f
p a r t s o r s c r e w s , i t i s n e c e s s a r y t o u s e t h e t h r e a d - l o c k o r l o c k t i t e
a d h e s i v e f o r t h e p a r t s o r s c r e w s w h i c h i n d i c a t e d o n m a n u a l .
R e c h e c k t h e s c r e w s o r n u t s t o m a k e s u r e t h e y a r e t i g h t e n e d a n d
a d h e r e d p r o p e r l y , e v e n f o r t h e p a r t s w h i c h w e r e p r e a s s e m b l e d .
組裝注意事項:
零件組裝時請依說 明書指示上膠,並適 度控制螺絲起子的扭力,以避免螺絲或 零 件
滑牙造成損壞,在 裝配原廠已完成組裝 之零件時,請再確認各螺絲是否確實鎖 緊 上 膠。
N o t e o f A s s e m b l i n g :
D o n o t t i g h t e n t h e s c r e w s t o o m u c h t h a t b r e a k t h e t h r e a d o f
p a r t s o r s c r e w s , i t i s n e c e s s a r y t o u s e t h e t h r e a d - l o c k o r l o c k t i t e
a d h e s i v e f o r t h e p a r t s o r s c r e w s w h i c h i n d i c a t e d o n m a n u a l .
R e c h e c k t h e s c r e w s o r n u t s t o m a k e s u r e t h e y a r e t i g h t e n e d a n d
a d h e r e d p r o p e r l y , e v e n f o r t h e p a r t s w h i c h w e r e p r e a s s e m b l e d .
CNC剪形臂
CNC Scissors Arm
Oil the part if it does not operate smoothly.
機件如有不順暢請適度添加潤滑油。
1
1
2
2
3
3
4
5
1
1
2
2
2
2
2
2
4
5
1
2
3
4
5
#A
#B
#B
#A
1
2
3
4
#A
#A
拉桿
4
4
Radius Arm
Rotor Head Assembly
旋翼頭總成組裝
Summary of Contents for Hurricane 255
Page 28: ......