background image

© 2006 General Binding Corporation

Page 2

GB

The information in this publication is provided for reference and is believed to be accurate and complete. General
Binding Corporation (GBC) is not liable for errors in this publication or for incidental or consequential damage in
connection with the furnishing or use of the information in this publication, including, but not limited to, any implied
warranty of fitness or merchantability for any particular use.

GBC reserves the right to make changes to this publication and to the products described in it without notice. All
specifications and information concerning products are subject to change without notice. Reference in this publication
to information or products protected by copyright or patent does not convey any license under the rights of GBC or
others. GBC assumes no liability arising from infringements of patents or any other rights of third parties.

This publication is copyrighted © 2006 by GBC. All rights reserved. The information contained in this publication is
proprietary and may not be reproduced, stored, transmitted, or transferred, in whole or in part, in any form without the
prior and express written permission of GBC.

Summary of Contents for 36002230




























Reviews: