38
I
METHOD FOR TACKING NEW
FILM TO EXISTING FILM
The following describes a method
for loading film whereby the
existing film present on the heat
rollers may be used in place of the
threading card to draw the new
film through the laminator. The
adhesive of the existing film must
be tacky or liquefied. Leading
edges of the new film will be
overlapped onto the tacky adhesive
of the old film. The existing film and
the new film will be pulled through
the laminator together.
1. Cut (1) remaining top film web
between the idler bar and heat
roller. Cut (2) the film web
between the lower film supply
and the idler bar (Figure 30).
CAUTION: Be careful not to cut
any of the rollers!
2. Remove the safety shield and tilt
the feed table down.
3. Do not allow the adhesive side
of the film to contact the heat or
pull rollers. Liquefied or tacky
adhesive deposited on heat
rollers will require the rollers to
be cleaned per the section
entitled
CARING FOR THE
FALCON 60+(-1) LAMINATOR.
4. Replace both the top and bottom
rolls of film with new rolls.
Ensure the adhesive side is
facing out.
5. Pull the film around the idler
bars, with the exception of PSA
mounting adhesives without a
release liner.
6. Tack the new film to the existing
film on the heat rollers. For PSA
film, attach the release liner to
the rewind tube (Figure 31).
7. Use the footswitch to advance
the film into the heat roller nip.
8. Observe the film being pulled
through the laminator to assure
that the remaining existing film
and the new film are advancing
concurrently. Any separation
between the films will require
stopping the motor immediately
and the situation corrected.
9. Press STOP (
) once the
newly threaded film has
completely exited the pull rollers.
Fig. 30
Fig. 31
(1)
(2)
(2)
= PSA film or mount adhesive
= PSA film or mount adhesive
Preliminary
Copy
Summary of Contents for Falcon 60+ (-1)
