background image

GBC 4064WF 

 

Operation Manual 

 

© 2005 General Binding Corporation  

 

Page 2 

 

 

ENG

 

 

The information in this publication is provided for reference and is believed to be accurate and complete. General Binding Corporation (GBC) is not liable for errors in 
this publication or for incidental or consequential damage in connection with the furnishing or use of the information in this publication, including, but not limited to, 
any implied warranty of fitness or merchantability for any particular use.  

GBC reserves the right to make changes to this publication and to the products described in it without notice. All specifications and information concerning products are 
subject to change without notice. Reference in this publication to information or products protected by copyright or patent does not convey any license under the rights 
of GBC or others. GBC assumes no liability arising from infringements of patents or any other rights of third parties. 

This publication is copyrighted © 2005 by GBC. All rights reserved. The information contained in this publication is proprietary and may not be reproduced, stored, 
transmitted, or transferred, in whole or in part, in any form without the prior and express written permission of GBC.

 

 

F

 

 

L’information contenue dans cette publication est fournie à titre de référence et elle est considérée exacte et complète. General Binding Corporation (GBC) n’est pas 
responsable des erreurs contenues dans cette publication ni des dommages indirects ou consécutifs portant sur l’utilisation ou la présentation de l’information de ce 
document, y compris, mais sans s’y limiter, toute garantie implicite de commercialité ou d’adaptation à un usage particulier. 

GBC se réserve le droit d’apporter des modifications à cette publication et aux produits qui y sont décrits sans préavis. Toutes les spécifications et l’information au sujet 
des produits sont sujettes à changements sans préavis. 

Toute référence à l’information ou aux produits protégés par un droit d’auteur ou un brevet présentée dans ce document ne porte aucune licence sous les droits de GBC 
ou d’autres parties. GBC n’assume aucune responsabilité découlant de contraventions aux brevets ou à tout autre droit de tierces parties. 

Cette publication est protégée par un droit d’auteur © 2003 de GBC. Tous droits réservés L’information contenue dans cette publication est privative et ne peut pas être 
reproduite, mise en mémoire, transmise ou transférée, en partie ou en entier, sous quelque forme que ce soit sans la permission écrite préalable et expresse de GBC.

 

 

 

La información contenida en esta publicación es proporcionada a título de referencia y se considera que es precisa y completa. General Binding Corporation (GBC) no 
es responsable por errores contenidos en esta publicación o por daños consecuentes o incidentales relacionados con la disponibilidad o el uso de la información en esta 
publicación, incluyendo y sin limitarse a, cualquier garantía de aptitud y comerciabilidad para cualquier uso específico. 

GBC se reserva el derecho de hacer cambios en esta publicación y a los productos descritos en la misma sin aviso previo. Todas las características y la información 
referente a los productos, están sujetas a cambios sin aviso previo. 

Las referencias en esta publicación a información o productos protegidos por derechos de propiedad intelectual o por patentes no otorga ninguna licencia amparada por 
los derechos de GBC u otros. GBC no asume ninguna responsabilidad que se derive de la violación de patentes u otros derechos de terceras partes. 

Copyright © 2003 Esta publicación está amparada por derechos de propiedad intelectual de GBC. Todos los derechos reservados. La información contenida en este 
documento es de propiedad exclusiva y no puede reproducirse, almacenarse, transmitirse o transferirse, en su totalidad o en partes, y de ninguna manera, sin la 
autorización previa y por escrito de GBC.

 

 

EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for GBC 4064WF




























Reviews: