ORCA-III Operation Manual
Operation
GBC Pro-Tech 1997 October
3-9
&ROG0RXQW /DPLQDWH
:LWK +RW 0DLQ 5ROOV
1.
See process chart 3-8 and diagram 3-8b for film
mounting instructions and machine adjustments.
2.
Move the feed table to the rear of the laminator.
3.
Raise the main roll (hot).
4.
Reverse the motor.
5.
Web according to drawing.
6.
Set the nip height and tack the leading edge for
the second pass. Run through as the liner is being
pulled off.
:LWK &ROG 0DLQ 5ROOV
1.
See process chart 3-9 and diagram 3-9b for film
mounting instructions and machine adjustments.
2.
Use the machine as a cold laminator with the
main rolls not heated.
5ROO WR 5ROO 7UDQVIHU DQG /DPLQDWH
2QH 3DVV
:LWK +RW 0DLQ 5ROOV
1.
See process chart 3-10 and diagram 3-10b for
film mounting instructions and machine
adjustments.
2.
Web the vinyl over the bottom roll and hold with
the pull rolls.
3.
It is useful to have a leader on the paper so it can
be webbed through and taped to the rewind
before starting.
4.
Lower the main roll, start the motor, and begin
the transfer process. Tape the finished product to
the rewind and add the lamination by raising the
pull roll. Web the laminate around the upper pull
roll. Be sure it is smooth on the roll, then lower
the roll.
5.
Add infeed and outfeed slitters as needed.
WARNING
The blades on both the infeed and outfeed
slitters are razor sharp. You can cut yourself
severely.
9LQ\O 7UDQVIHU
1.
See process chart 3-11 and diagram 3-11b for
film mounting instructions and machine
adjustments.
2.
Web the vinyl up around the bottom main roll
and over to the pull roll. Make sure the material
is webbed straight and lower the pull roll to hold
the vinyl.
3.
Place both table idlers in the slots on the table
brackets. Web the paper through as shown in
diagram 2-11b.
4.
Often, when paper is not on a core, hand tension
must be applied to the paper in order to maintain
transfer quality until the end of the transferred
image.
5ROO WR 5ROO 7UDQVIHU
:LWK +RW 0DLQ 5ROOV
1.
See process chart 3-12 and diagram 3-12b for
film mounting instructions and machine
adjustments.
2.
Web the vinyl up around the bottom main roll
and over to the pull roll. Lower the pull roll to
hold the vinyl.
3.
Web the paper up to the main roll. Lower the
main roll to start the transfer process.
4.
Tape the vinyl onto the lower rewind and peel off
the paper. Wind it on the upper rewind.
5.
Lamination can be done in a second pass, if
required. See chart 2-13.
Summary of Contents for OORCA-III
