Operations Manual
Page 13
T
ALON
44/64
CE
©2004 General Binding Corporation
Fig 3
Pre- Installation
Before a Talon 44/64 Laminator can be installed, ensure
the following requirements are met;
1.
Are doorways and hallways wide enough for the lami-
nator to be moved to the installation site?
2.
Is there ample room for the laminator?
– A work area must be established that allows for opera-
tion in both the front and rear of the laminator and
provides space for efficient material flow. (Figure 3)
3.
Is the environment appropriate for the laminator?
– The laminator requires a clean, dust and vapor free
environment to operate properly.
– Avoid locating the laminator near sources of heat or
cold. Avoid locating the laminator in the direct path of
forced, heated or cooled air.
CAUTION:
Air flow can cause uneven heating/ cooling of
the rollers and result in poor output quality.
4.
Have you contacted a certified electrician to wire the
receptacle and ensure that adequate power is being
supplied, having the appropriate capacity, over current
protection and safety lockouts available?
Talon 44 requires:
– 380-400V 50/60 Hz, 3 phase 5 wire, 16 amp service
required.
Machine is supplied with:
Cord
– manufacturer: SCAME PARRE
– type: 211.3237
– rating: 346V-415V, 32A, 3P+N+E
Plug
– manufacturer: LAPP KABEL
– type: OLFLEX CLASSIC-110
– rating: 5 × 4.0 mm²
Talon 64 requires:
– 380-400V 50/60 Hz, 3 phase 5 wire, 16 amp service
required.
Machine is supplied with:
Cord
– manufacturer: SCAME PARRE
– type: 211.3237
– rating: 346V-415V, 32A, 3P+N+E
Plug
– manufacturer: LAPP KABEL
– type: OLFLEX CLASSIC-110
– rating: 5 × 4.0 mm²
20 ft.
( 508 ) cm
13 ft
( 330 cm )
3 ft
( 91 cm )
8 ft 8 in
( 220 cm )
8 ft 8 in
( 220 cm )
4 ft. x 6 ft.
(101.6 x 152 cm)
Work table on wheels
Electrical cord
drop
Front
Back
4 ft. x 6 ft.
(101.6 x 152 cm)
Work table on wheels
Electrical cord
drop
4 ft. x 6 ft.
(101.6 x 152 cm)
Work table on wheels
Back
Front
4 ft. x 6 ft.
(101.6 x 152 cm)
Work table on wheels
Summary of Contents for Talon 44 CE
