background image

PRINTED IN CHINA                                                     MADE IN CHINA

CAUTION :

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and the  receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.

Little function tip

This fireplace features a "Calibration" function which allows you to adjust the Thermostat reading
so that it matches the thermostat in your home.   To calibrate, press and hold the TIMER button
for a few seconds until the display shows 0

.  Then, press the UP or DOWN key to adjust the

Thermostat reading to the desired level.  The calibration function has an adjustment range of

+9

 to -9 

.

Limited warranty for 1 year

Customer service number : 1888-878-8820

Working hours : Mon-Fri, 8:30am - 5:30pm, Pacific standard time.

18

Summary of Contents for SWE137B-2



















Reviews: