background image

TABLE OF CONTENTS 

GENERAL INFORMATION ................................................................ 4 

FEATURES ..................................................................................... 4 

INSTALLATION .................................................................................... 5 

CONNECTING TO THE ADSL LINE INTERFACE ........................  6 
CONNECTING THE LAN (ETHERNET) INTERFACE ..................  7 
CONNECTING POWER .............................................................. 8 

OPERATION ........................................................................................ 9 

POWER UP ..................................................................................... 9 
FRONT PANEL LED STATUS MONITORS .............................. 9 

CUSTOMER SERVICE ................................................................ 11 

SERVICE AND UNRESOLVED PROBLEMS .......................... 11 

APPENDIX A ............................................................................ 12 

SPECIFICATIONS ................................................................... 12 

APPENDIX B .............................................................................. 14 

FACTORY REPLACEMENT PARTS AND ACCESSORIES ..... 14 

APPENDIX C .............................................................................. 15 

INTERFACE PIN ASSIGNMENT .............................................. 15 

3

Summary of Contents for XC-NT200

















Reviews: