background image

4

BEFORE YOU START: 

OPENING SIZE

BEFORE YOU START: 

SIDE CLEARANCE

Opening  

height

Opening width + overlap

Opening width 

Garage opening 

viewed from the inside

Door curtain roll

Curtain 
overlap

Curtain 
overlap

Door curtain size

Up to  2896mm (9’6”) wide & 

2438mm (8’0”) high

Over 2896mm (9’6”) wide &  

2438mm (8’0”) high

Guide size

30mmª

50mm

Overlap  

each side

25mmª

50mm

OPENING WIDTH:

  

DuraRoll garage doors fit behind the garage opening. 
Check that the door curtain supplied overlaps the opening 
width at each side by the minimum requirements:

ªIn Ireland all door sizes are supplied with 50mm guides

OPENING HEIGHT: 

 

The door will fit any opening height 

up

 to that 

stated on the packaging, e.g. a 2134mm high door 
can be fitted to a 2000mm high opening

Lintel

Opening 

Width

Opening 

Height

Side 

Clearance

Side 

Clearance

Headroom

Backroom

Side clearance

Garage opening 

viewed from the inside

Door curtain size

Up to 2896mm (9’6”) wide & 

2438mm (8’0”) high

Up to 2896mm (9’6”) wide

Over 2896mm (9’6”) wide & 

2438mm (8’0”) high

Over 2896mm (9’6”) wide

Guide 

size

30mmª

30mmª

50mm

50mm

Side clearance 

for manual doors

95mmª

each side

95mmª

each side

120mm

each side

120mm

each side

Side clearance for  

doors with a motor

135mmª motor side

95mm non-motor side

165mmª motor side

95mm non-motor side

160mm motor side

120mm non-motor side

190mm motor side

120mm non-motor side

How much room do I need at the side of the garage opening?
The door is mounted onto brackets and the brackets must be set 
in from the side of the garage opening by the minimum distance 
to the outside edge of the bracket as shown in the table below.
Doors with a motor require extra clearance on the side the motor 
is fitted - see table below.
To achieve the minimum side clearance you will need to cut the 
ends of the door axle.  

STANDARD DOORS 

MINI DOORS

 

 

STRUCTURAL CONDITIONS OF OPENING:

 

The surface where the door is to be fitted must be flush and reasonably smooth. Small irregularities in 
brick work will be acceptable. The lintel must not protrude backwards or forwards from the brick piers.

!

!

ªIn Ireland all door sizes are supplied with 50mm guides

www.samsondoors.co.uk

0800 328 6250

www.samsondoors.co.uk

www.samsondoors.co.uk

0800 328 6250

www.samsondoors.co.uk

Summary of Contents for DuraRoll





















Reviews: