background image

9

Mark the fixing position of the bracket 

STANDARD DOOR

Distance from the bottom of the lintel to the top of the bracket: 

A=200mm

 

Minimum headroom above the bracket 

B=231mm* (doors up to 8’0”/2438mm high)
B=283mm* (doors over 8’0”/2438mm high)

For the full height of the opening to be available

A+B=431mm* (doors up to 8’0”/2438mm high)
A+B=483mm* (doors over 8’0”/2438mm high)

If the full headroom is not available (A+B=431mm/483mm), 
the bracket can be fixed 241mm*/293mm* below the ceiling 
with the door curtain projecting down into the opening by up to 
a maximum of 100mm when fully open without the need for a 
fascia - see page 5 for detail drawings.
The minimum distance from the edge of the opening to the 
bracket is:

D= Curtain overlap (C) + 10mm min 
D= Curtain overlap (C) + 185mm max

 

MINI  DOOR

A=140mm

 from the bottom of the lintel to the top of the 

bracket

B=203mm*

 minimum headroom above the bracket

A+B=343mm*

 for the full height of the opening to be available 

with the door fully open
If the full headroom is not available (A+B=343mm), the bracket 
can be fixed 213mm below the ceiling with the door curtain 
projecting down into the opening by up to a maximum of 
100mm when fully open without the need for a fascia. 
The minimum distance from the edge of the opening to the 
bracket is:

D=Curtain overlap (C) + 10mm min  
D=Curtain overlap (C) + 185mm max

*Note: 10mm more headroom is required to install the 
door than is needed to operate the door once installed. 
If the available headroom is right at the minimum, the 
bracket can be fixed 10mm lower whilst the door roll 
is fitted and tensioned and then tapped up by 10mm 
once the door is installed to give full clearance with no 
hangdown. If this is the case, fix the brackets through 
the slotted holes (step 1) to allow for tapping up once 
the door roll is installed.

PARTS REQUIRED

2x

B

E 2x

1x

A

LR

UN

C 2x LR

UN

F 2x

FIXINGS REQUIRED

2

x6

OR

1

x6

1

2

!

!

CHECK LEVELS

Fix the brackets in place at each 

side of the opening. 

www.samsondoors.co.uk

0800 328 6250

www.samsondoors.co.uk

www.samsondoors.co.uk

0800 328 6250

www.samsondoors.co.uk

Summary of Contents for DuraRoll





















Reviews: