manualshive.com logo in svg

GE Grid Solutions F60, Instruction Manual

The GE F60 Instruction Manual is a comprehensive guide that provides users with detailed information on operating and maintaining this reliable product. Obtain a free download of this essential manual from our website, ensuring convenient access to the instructions you need to optimize the performance of your GE F60.

Share
Download
background image

GE Multilin

F60 Feeder Protection System

B-1

APPENDIX B 

B.1 MODBUS RTU PROTOCOL

B

APPENDIX B MODBUS COMMUNICATIONSB.1MODBUS RTU PROTOCOL

B.1.1 INTRODUCTION

The UR series supports several communications protocols to allow connection to equipment such as personal computers,
remote terminal units (RTUs), supervisory control and data acquisition (SCADA) masters, and programmable logic control-
lers. The Modicon Modbus protocol is the most basic protocol supported by the UR. Modbus RTU is available via the
RS232 and RS485 serial links, and Modbus TCP/IP is available over Ethernet. The following description is intended primar-
ily for users who want to develop their own master communication drivers. Note that:

•

The UR always acts as a slave device, meaning that it never initiates communications. It listens and responds to
requests issued by a master computer.

•

A subset of Modbus RTU and Modbus TCP/IP protocol format is supported that allows extensive monitoring, program-
ming, and control functions using read and write register commands.

B.1.2 PHYSICAL LAYER

Each data byte is transmitted in an asynchronous format consisting of 1 start bit, 8 data bits, 1 stop bit, and possibly 1 parity
bit. This produces a 10 or 11 bit data frame. This can be important for transmission through modems at high bit rates (11 bit
data frames are not supported by many modems at baud rates greater than 300).

The faceplate RS232 port is intended for local use and is fixed at 19200 bit/s baud and even parity. The rear terminal
RS485 port can be set for baud rates of 300, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 33600, 38400, 57600, or
115200 bps, and even, odd, and no parity options are available. See the 

Communications

 section of chapter 5 for details.

The Modbus TCP/IP protocol is available on each of the rear Ethernet ports. These ports are 100Base-FX.

B.1.3 DATA LINK LAYER

Modbus RTU communications takes place in packets that are groups of asynchronously framed byte data. The master
transmits a packet to the slave and the slave responds with a packet. The following information describes the general for-
mat for both transmit and receive packets. For details on packet formatting, see subsequent sections describing each func-
tion code.

•

SLAVE ADDRESS:

 This is the address of the slave device that is intended to receive the packet sent by the master

and to perform the desired action. Each slave device on a communications bus must have a unique address to prevent
bus contention. All of the relay’s ports have the same address which is programmable from 1 to 254; see chapter 5 for
details. Only the addressed slave will respond to a packet that starts with its address. Note that the faceplate port is an
exception to this rule; it will act on a message containing any slave address.

A master transmit packet with slave address 0 indicates a broadcast command. All slaves on the communication link
take action based on the packet, but none respond to the master.

•

FUNCTION CODE: 

This is one of the supported functions codes of the unit which tells the slave what action to per-

form. See the 

Supported Function Codes

 section for details. An exception response from the slave is indicated by set-

ting the high order bit of the function code in the response packet. See the 

Exception Responses

 section for details.

•

DATA:

 This will be a variable number of bytes depending on the function code. This may include actual values, set-

tings, or addresses sent by the master to the slave or by the slave to the master.

•

CRC:

 This is a two byte error checking code. The RTU version of Modbus includes a 16-bit cyclic redundancy check

(CRC-16) with every packet which is an industry standard method used for error detection. If a Modbus slave device
receives a packet in which an error is indicated by the CRC, the slave device does not act upon or respond to the

Table B–1: MODBUS RTU PACKET FORMAT

DESCRIPTION

SIZE

SLAVE ADDRESS

1 byte

FUNCTION CODE

1 byte

DATA

N bytes

CRC

2 bytes

DEAD TIME

3.5 bytes transmission time

Summary of Contents for F60





































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for F60

P.Lindberg 9058322 Original Manual preview
9058322
Brand: P.Lindberg Pages: 41
Tektronix 80A09 Instructions preview
80A09
Brand: Tektronix Pages: 5
Middle Atlantic FlexView Series Instruction Sheet preview
FlexView Series
Brand: Middle Atlantic Pages: 10
Dräger R56963 Assembly Instructions preview
R56963
Brand: Dräger Pages: 4
Solera FV221016 Quick Start Manual preview
FV221016
Brand: Solera Pages: 4
Falltech DuraTech Cable SRL User Instruction Manual preview
DuraTech Cable SRL
Brand: Falltech Pages: 31
3M Pro-Protect Manual preview
Pro-Protect
Brand: 3M Pages: 53
ABB ret650 Product Manual preview
ret650
Brand: ABB Pages: 70
ABB REL 531 Installation And Comissioning Manual preview
REL 531
Brand: ABB Pages: 140
ABB Relion 611 Series Engineering Manual preview
Relion 611 Series
Brand: ABB Pages: 108
ABB Relion Technical Manual preview
Relion
Brand: ABB Pages: 778
Innotech LIFELINE-KIT Instruction Manual preview
LIFELINE-KIT
Brand: Innotech Pages: 33
Endress+Hauser HAW569 Quick Start Manual preview
HAW569
Brand: Endress+Hauser Pages: 2
Centrosolar Solara Cell-Protector Installation preview
Solara Cell-Protector
Brand: Centrosolar Pages: 4

Brands by name

Popular brands

Load more brands