background image

 

 

© 2003 Kalatel, a GE Interlogix company 

All Rights Reserved. 

 
Any GE Interlogix, Kalatel division, software supplied with GE 
Interlogix, Kalatel division, products is proprietary and furnished 
under license and can be used or copied only in accordance 
with the terms of such license. 

This document contains proprietary information that is protected 
by copyright. No part of this document may be reproduced or 
transmitted in any form or by any means without the prior written 
permission of GE Interlogix, Kalatel division. 

 

 

The information contained in this document is subject to change 
without notice. GE Interlogix, Kalatel division, in keeping pace 
with technological advances, is a company of product 
innovation. Therefore, it is difficult to ensure that all information 
provided is entirely accurate and up-to-date. GE Interlogix, 
Kalatel division, accepts no responsibility for inaccuracies or 
omissions and specifically disclaims any liabilities, losses, or 
risks, personal or otherwise, incurred as a consequence, directly 
or indirectly, of the use or application of any of the contents of 
this document. 

For the latest product specifications, visit GE Interlogix, Kalatel 
division, online at www.kalatel.com or contact your GE 
Interlogix, Kalatel division, sales representative. 

For technical support before and after installation, call 800-
469-1676. 

Technical support is available 24 hours a day, 7 days a week. 

Call: 

Tech Support

 

800-469-1676 (6 A.M. – 5 P.M. PST 

Monday through Friday) 
 

Tech Support

 

541-740-3589 (all other times) 

 

Main

 

800-343-3358 or 541-754-9133 

Fax: 

Tech Support

 

541-752-9096 (available 24 hours a day) 

 

Main

 

541-754-7162 

Web: 

www.kalatel.com 

0150-0263A / May 2003 

 

This equipment has been tested and 
found to comply with the limits for a 
Class A digital device, pursuant to part 
15 of the FCC Rules. These limits are 
designed to provide reasonable 
protection against harmful interference 
when the equipment is operated in a 
commercial environment. This 
equipment generates, uses, and can 
radiate radio frequency energy and, if 
not installed and used in accordance 
with the instruction manual, may cause 
harmful interference to radio 
communications. 

You are cautioned that any changes or 
modifications not expressly approved by 
the party responsible for compliance 
could void the user's authority to 
operate the equipment.

 

Summary of Contents for Interlogix BusSecure






































Reviews: