manualshive.com logo in svg

GE Interlogix NetworX NX-8, Installation Manual

The GE Interlogix NetworX NX-8 is a top-notch security system designed to safeguard your home or business. With its comprehensive Installation Manual, you can easily set up and customize the system to meet your specific needs. Download the user manual for free from our website and enjoy the peace of mind you deserve.

Share
Download
background image

Page 22

L

LOCATION 40 - SYSTEM TIMERS (10 segments, numerical data)

Location 40 contains the duration of various system timing functions. Example: If you desire the duration of the
Dynamic Battery Test to be 30 minutes, you should program [3]-[0]-[

r

] in segment 1 of this location. The [3]-[0] is the

number of minutes, and the [

r

] stores the data and moves to the next segment of this location.

 

Segment 1 - Dynamic Battery Test duration in minutes 0-255 minutes ("0" = no test)
Segment 2 - AC Fail report delay in minutes 0-255 minutes.
Segment 3 - Power Up Delay in seconds 0-60 seconds ("0" = no power up delay).
Segment 4 - Siren Time in minutes 1-255 minutes.
Segment 5 - Telephone Line Cut delay in seconds 0-255 seconds ("0" = no TLM).
Segment 6 - Cross Zone time in minutes 0-255 ("0" = no cross zoning).
Segment 7 - Chime time in 50 mS (1/20th second) increments from 0-12 seconds ("0" = follows zone 255 latched).
Segment 8 - Dial delay in seconds 0-255 seconds (“0 ” = no abort delay).
Segment 9 - Fire Alarm Verification time in seconds 120-255 seconds ("0" = no fire alarm verification). NOTE:

This feature is not approved for residential use in California

Segment 10 -Listen-In time in seconds 0-255 ("0" = no Listen-In time).

Note: The "Listen-In" feature cannot be enabled for UL Listed systems. The "Dynamic Battery Test" feature
cannot exceed four (4) hours. The dial delay shall be set to -0-.

LOCATION 41 - SPECIAL FEATURES (1 segment, feature selection data)

Segment 1:

1 -

On enables the 6-digit code option. If 6-digit option is enabled, all arm/disarm codes and the "Go To
Program Code" are 6 digits. If this option is enabled, the default user 1 code is [1]-[2]-[3]-[4]-[5]-[6].
NOTE: IF YOU ENABLE THIS OPTION, VERIFY THAT THE "GO TO PROGRAM CODE" IS A SIX-
DIGIT CODE BEFORE EXITING PROGRAMMING.

2 -

On requires code entry for [

r

]-[9]-[8] (perform call back download) and [

r

]-[9]-[9] (answer incoming call for

download) functions.

3 -

Enable Auto Cancel / Abort (Refer to feature definitions beginning on page 3)

4 -

Enable Walk-Test Mode (Refer to feature definitions beginning on page 3)

5-8

Reserved.

L

LOCATION 42 - GO TO PROGRAM CODE (6 segments, numerical data)

Location 42 contains the "Go To Program Code". This location contains either a 4 or 6-digit code. If the 6-digit code
option is enabled in Location 41, THIS CODE MUST CONTAIN SIX (6) DIGITS. If this option is not enabled in
location 41, the last 2 segments (digits) will be ignored. With the NX-8 disarmed, the "Go To Program Code" can be
used to enter the Program Mode.

LOCATION 43 - GO TO PROGRAM CODE PARTITION AND AUTHORIZATION (2 segments, feature selection)
The "Go To Program Code" can be used as a standard arm/disarm code. When using the code to arm or disarm, the
user ID is 255. (This code may not be changed in the Run Mode.)

Segment 1:

1 - Reserved.
2 - On enables "Go To Program Code" as an arm only code.
3 - On enables "Go To Program Code" as an arm only after closing.
4 - On enables "Go To Program Code" as a master arm/disarm code (can change user codes)
5 - On enables "Go To Program Code" as an arm/disarm code.
6 - On enables "Go To Program Code" to bypass zones.
7 - On enables "Go To Program Code" opening and closing reports.
8 - Reserved.

Segment 2:

1 - On enables the "Go To Program Code" for Partition #1.
2 - On enables the "Go To Program Code" for Partition #2.
3 - On enables the "Go To Program Code" for Partition #3.
4 - On enables the "Go To Program Code" for Partition #4.
5 - On enables the "Go To Program Code" for Partition #5.
6 - On enables the "Go To Program Code" for Partition #6.
7 - On enables the "Go To Program Code" for Partition #7.
8 - On enables the "Go To Program Code" for Partition #8.

L

LOCATION 44 - DURESS CODE (6 segments, numerical data)

Summary of Contents for NetworX NX-8






























































Reviews:

No comments

Related manuals for NetworX NX-8

Ziton ZP2 Series Quick Installation Manual preview
ZP2 Series
Brand: Ziton Pages: 2
Ziton zp1-f Series Quick Operation Manual preview
zp1-f Series
Brand: Ziton Pages: 2
Araani Fire Guard User & Installation Manual preview
Fire Guard
Brand: Araani Pages: 42
Cooper Wheelock RSS-24MCCH Installation Instructions preview
RSS-24MCCH
Brand: Cooper Wheelock Pages: 4
Vighnaharta TSFC 24-2 User Manual preview
TSFC 24-2
Brand: Vighnaharta Pages: 26
MEDC PBI Technical Manual preview
PBI
Brand: MEDC Pages: 8
Aico Ei169 Product Manual preview
Ei169
Brand: Aico Pages: 15

Brands by name

Popular brands

Load more brands