background image

To reduce the risk of electric shock,

 this appliance has a polarized plug (one blade wider than the other). This plug

will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Afin de réduire le risque de choc électrique,

 cet appareil est muni d’une fiche polarisée (une des lames est plus

large). Cette fiche ne peut être insérée dans une prise polarisée que d’une seule façon. Si la fiche ne peut être
insérée dans la prise, retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une
prise adéquate par un électricien qualifié. Ne pas modifier la fiche.

General Information

The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner
to prevent hose clogs.

DO NOT OIL 

the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.

Customer Assistance

The instructions in this booklet serve as a guide to routine maintenance. For additional service information please
call, 1-877-556-0973. 

You should know the model, type and serial numbers when you call.

3

Rating Plate

The model, type, and serial numbers are indicated on
the rating plate located on the underneath side of the
cleaner. For prompt and complete service information,
always refer to these numbers when inquiring about
service.

Model & Type__________________________

Serial No. _____________________________

Thermal Cut Off

This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner
suddenly shuts off, turn the switch off and unplug the cleaner. Check the cleaner for a possible source of overheating
such as a blocked hose or clogged filters. If these conditions are found, fix them and wait at least 30 minutes before
attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch. If the
cleaner still does not run, then call 1-877-556-0973 for customer assistance.

Summary of Contents for 106585




















Reviews: