1
To assemble the tree top,
properly align and insert the
"TOP" section into the top of
section "B". (See Fig. D)
Adjust branch tips, as needed,
for a fuller look.
7
2
The tree stand should be open and
set at 90° angle.
8
Gently press on foot pedal
to select the desired lighting
function. (See below)
a. This tree is provided with an extension cord for a tree
topper, which can be attached to the top section
along the pole.
b. As an option, the tree adapter can be plugged into the
back of the tree top extension cord as an add-on.
This feature allows you to utilize only one outlet.
IMPORTANT:
Store your carton neatly in a cool, dry location protected from sunlight
to prolong the tree life and to better keep the light sets in working order. Do not place
a heavy load on the carton to avoid damage to or crushing the carton and tree inside.
NOTE:
No tools required
DISCLAIMER :
DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS LIGHTING
OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS
MAY RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL
INJURY. DOING THIS, WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF
THIS PRODUCT.
Disconnect the decorative item from the power source before
performing any maintenance or cleaning.
For indoor use only
120V
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
GE is a trademark of General Electric Company
and is under license by Nicolas Holiday Ltd.
4
Untie RED twist-tie to release branch
panels. All branches should fall into
place with a gentle pull on the outer
layer of branches.
B
A
TOP
7.5 FT TREE
2
1
90°
Thumbscrew
Repeat “Step 4” for shaping.
6
To assemble the section labeled
"B", properly align and insert
section "B" into the top of
section "A". (See Fig. C)
Adjust branch tips, as needed,
for a fuller look.
5
3-amp
2 pcs
Qty
Spare parts
included
©2021 Nicolas Holiday Ltd.
9 F., No. 37, Guangfu North Rd., Taipei, Taiwan 10560 All rights reserved.
Printed in China
20121LO
Tree Sections
Tree Stand
Approx. Asm Time*
7.5 ft tree
3
Metal
5 – 10 minutes
TREE ASSEMBLY DIAGRAM
7.5 FT
TOP
B
A
AC CONNECTOR
FOR
TREE TOP
Color change
foot pedal
SCHEMATIC DIAGRAM
Tree Extension
Cord
Easy Light
Technology
®
Tree Stand
OPEN
TOP
A
B
Tree Stand
Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas
tree. Should you have any problems with your tree, visit us at
www.geholidaylighting.com
for more information. You can call our
toll free number at 1-877-398-7337.
Check our website for latest service hours and assembly instruction videos.
Pre-Lit Christmas Trees
Pre-Shaped
naturally positioned branch tips,
create the look of a natural tree
Easy Light Technology
®
eliminates cord connections
Color Choice
®
LED Technology
Assembly Instructions
Carefully unpack the carton.
Remove bubble wrap and
inspect the sections of your tree.
The carton should include sections
labeled "A", "B" and "Top", as well
as a Tree Stand.
3
Insert Section labeled A into tree
stand, tighten the thumbscrew.
Then insert the plug into an
electrical wall outlet.
It is important that
you align the mark
when you connect
two tree sections.
Fig. C
It is important that
you align the mark
when you connect
two tree sections.
Fig. D
Tree Storage
1. Remove the tree’s main extension cord
plug from the wall outlet.
2. Starting at the top, disconnect the "TOP"
from section "B" and then disconnect
section "B" from section "A".
{Fig. 1}
Note:
Care should be taken to avoid
damage to the lights.
3. Remove section "A" from the tree stand
and close tree stand to place into the carton.
4. Refer to the drawing on how to repack
your tree.
{Fig. 2}
Troubleshooting Tips
If the tree does not illuminate, try stepping on the
Color change foot pedal
and make certain the wall switch is turned on. If one section of your tree does
not illuminate, check that section for cut or damage wires or that all electrical
connections on tree are made. Due to unique construction of the light sets, the
individual LEDs are not replaceable. The light sets are designed for continued
operation even if an individual LED fails to light.