GE 24906 - Remote Control With Glow Keys Instruction Manual Download

Page: 7 / 16

Write your codes down here for easy reference

later.

Direct Code Entry

1. Press and hold the

CODE SEARCH

button until the red indicator stays on,

then release the

CODE SEARCH

button.

2. Press and release the desired device

button (

VCR

, etc.). The red indicator

blinks, then stays lit.

3. Enter the 4 digit code

from the code tables

(on separate sheet).

Note: after a valid

code entry, the red

indicator turns off. For

an invalid code, the

red indicator flashes.

4. With your device on, press

ON•OFF

If the device turns off, no further

programming is required. Note: If

some buttons do not operate your

equipment, try one of the other

codes for your brand.

Device

Device stored Code

VCR
CBL/SAT
DVD/AUX

Summary of Contents for 24906 - Remote Control With Glow Keys

















Search results

Summary of Contents for 24906 - Remote Control With Glow Keys

Reviews:

Related manuals for 24906 - Remote Control With Glow Keys

Brands by name

Popular brands

GE 24906 - Remote Control With Glow Keys, Instruction Manual

Search results

Summary of Contents for 24906 - Remote Control With Glow Keys

Reviews:

Related manuals for 24906 - Remote Control With Glow Keys

Brands by name

Popular brands