background image

                                             

49-Tomberlin Emerge (262E1_262TB1_403TB1) Install Sheet-370   Rev 02  11/29/18   

Sheet 2 of 4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Diagram shows the back (wire) side of Connector 

262E1, 262TB1, 

403E1, 403TB1 

Controller 

FUS

P1 

(B+ from Run/Tow Switch)

 

For 

P4 

(Forward In)

 

Rev 

P5 

(Reverse In)

 

Reverse 

Alarm 

P10 

(Backup Alarm Out)

 

Run/Tow           

Switch 

 (Pot Wiper In)

 P7 

 

Speed        

Sensor 

Out

 

 (Speed Sensor Supply Out)

 P15 

F1 

48V Battery Pack 

B- 

B+ 

Main Solenoid            

Contacts 

F1 

Motor 

Field 

F2 

F2 

 (Speed Sensor In)

 P14 

 (Speed Sensor Return Out)

 P16 

Main Solenoid Coil 

P3 

(Pedal Switch In)

 

Foot Pedal 

 

P2 

(B+ from Run/Tow Switch)

 

P11 

(Main Solenoid Out)

 

P6 

(Key Switch In)

 

PC/Run Switch 

Key Switch 

Sense 

Circuit 

E-Z-GO      

ITS 

PCB 

Tomberlin Converter 

PCB w/E-Z-GO ITS 

Option #1 (Obsolete) 

Option #2 (Current) 

Sense 

Circuit 

TOMBERLIN ITS 

B+ 

B- 

B+ 

B- 

OR 

 

OR 

 

0-5V 

0-5V 

Tomberlin p/n: 1007918 & 1008284 

A1 

Motor 

Armature 

A2 

A2 

A1 

P17 

(Main Solenoid Out) 403E1/TB1 model 

 

Summary of Contents for 262E1

Page 1: ... 11 Pin 17 on 403E1 TB1 on the controller Be sure to check diode functionality with VOM prior to install If pre charge resister is installed please remove This control is equipped with an internal resistor and installing one on the solenoid could cause damage to the control CHECK THE CART WIRE HARNESS Check the connectors on the wire harness for corrosion loose broken burnt or missing pins Repair ...

Page 2: ... Sensor Supply Out P15 F1 48V Battery Pack B B Main Solenoid Contacts F1 Motor Field F2 F2 Speed Sensor In P14 Speed Sensor Return Out P16 Main Solenoid Coil P3 Pedal Switch In Foot Pedal P2 B from Run Tow Switch P11 Main Solenoid Out P6 Key Switch In PC Run Switch Key Switch Sense Circuit E Z GO ITS PCB Tomberlin Converter PCB w E Z GO ITS Option 1 Obsolete Option 2 Current Sense Circuit TOMBERLI...

Page 3: ... If not 0 volts check wiring and Pc Run Switch for an open condition Pin 4 With F R Switch in Reverse must equal 0 volts If not 0 volts check wiring and F R Switch for a shorted condition Pin 4 With F R Switch in Forward must equal Pack Voltage If not Pack Voltage check wiring and F R Switch for an open condition Pin 5 With F R Switch in Forward must equal 0 volts If not 0 volts check wiring and F...

Page 4: ... 17 on 403E1 TB1 With Pedal Down must equal approximately 0 volts If not approximately 0 volts check terminal for being burnt corroded If terminal is clean controller may be defective Upgrade Note If upgrading from 262 to the 403 pin 11 will need to be moved to pin 17 location Helpful Hints DO NOT UNDER ESTIMATE THE IMPORTANCE OF MOTOR RESISTANCE CHECKS AND MAIN SOLENOID CHECKS MANY CART ISSUES AR...

Reviews: