49-7805-1
5
Controls
Features and appearance will vary.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
Fan
Fan
Mode select
Fan speed
Decrease
Temperature
set Increase
and Decrease
Auto Fan on
Fan speed
Increase
8QLWSRZHU
on/off
NOTE:
The display always shows the room temperature except
when setting the set temperature.
Power
On/Off
Fan
Mode
Auto
Reset
Filter
High
Med
Low
Cool
Fan Only
Energy Saver
Connect
Set
+
-
WiFi
8
Light indicates
WiFi connection
Light indicates the unit is in
the temperature set mode.
Controls
NOTE:
When the bucket is full or removed, the controls
cannot be set.
1. Power Pad
Turns air conditioner on and off. When turned on, the
display will show the room temperature.
2. Display
Shows the room temperature. Shows the Set
temperature while setting the temperature in
Cool
or
Energy Saver
modes. The Set light will turn on while
setting.
3.
7HPS,QFUHDVHŸ'HFUHDVHź3DGV
8VHWRVHWWHPSHUDWXUHZKHQLQ&RRORU(QHUJ\6DYHU
mode. The Set light will turn on while setting.
4. Fan Speed Pads
8VHWRVHWWKHIDQVSHHGWR
Low, Med, High
or
Auto
on the unit.
NOTE:
On the remote control, use the fan
speed
In / Decrease –
pads to set the fan
speeds to
Low
,
Med
or
High
8VHWKH
Auto
pad to turn
Auto
fan on.
5. Mode Pad
8VHWRVHWWKHDLUFRQGLWLRQHUWR
Cool
,
Energy
Saver
or
Fan
Only
mode.
6. WiFI Connect
Enables connection of the air conditioner to the home
WiFi. Download App for details at
www.GEAppliances.
com/connect
.
7. Reset Filter
LED will turn on when fan has accumulated 250 hours of
run time as a reminder to clean filter. Press
Reset Filter
to turn off the LED and reset the accumulated run time.
NOTE:
The default temperature reading on the display
is degree Fahrenheit ( °F). To change the display to
degree Celsius (°C), press the Temp Increase
Ÿ
and
Temp Decrease
ź
buttons together and hold for 3
seconds. Repeat the process to change back to degree
Fahrenheit (°F)
8. Control Display On and Off
To reduce brightness during sleeping hours, this air
conditioner control display has an automatic off feature
where the control display will turn off completely after 5
minute of inactivity. To illuminate the control interface,
press any button on the control display or remote
control. The control display will illuminate all previously
illuminated LED’s. The control interface will now respond
to any prescribed button press after it is illuminated.
Press and hold the FAN button to toggle this feature ON
or OFF. The LED’s will now stay ON anytime the unit is
ON.
Do Not Operate in Freezing Outdoor Conditions
This cool-only air conditioner was not designed for
freezing outdoor conditions. It must not be used in
freezing outdoor conditions.
Remote Control
Ŷ7RHQVXUHSURSHURSHUDWLRQDLPWKHUHPRWHFRQWURODW
the signal receiver on the air conditioner.
Ŷ0DNHVXUHQRWKLQJLVEHWZHHQWKHDLUFRQGLWLRQHUDQG
the remote control that could block the signal.
Ŷ7KHUHPRWHFRQWUROVLJQDOKDVDUDQJHRI
up to 20 feet.
Ŷ0DNHVXUHEDWWHULHVDUHIUHVKDQGLQVWDOOHGFRUUHFWO\DV
indicated on the remote control.
Ŷ5HPRWHFRQWDLQVDPDJQHWDOORZLQJLWWRDWWDFKWR
metal surfaces.
Summary of Contents for AEC08
Page 16: ...16 49 7805 1 NOTES Notes ...
Page 34: ...16 49 7805 1 NOTA Nota ...
