4
About the controls on the air conditioner.
Features and appearance will vary.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
Fan
Fan
Delay 1–24hr
Delay timer
Decrease
Mode select
Fan speed
Decrease
Temperature
set Increase
and Decrease
Delay
timer
Increase
Auto Fan
on
Fan speed
Increase
Unit power
on/off
Air Conditioner Controls
Controls
1. Power Pad
Turns air conditioner on and off. When turned on, the display
will show the room temperature.
2. Display
Shows the room temperature or time remaining on the
Delay timer. Shows the
Set
temperature while setting the
temperature in
Cool
or
Energy Saver
modes. The
Set
light will
turn on while setting.
3. Temp In
/Decrease –
Pads
Use to set temperature when in
Cool
or
Energy Saver
mode.
The
Set
light will turn on while setting.
4. Delay Timer In
/Decrease –
Pads
Each touch of the
Increase
+
/
Decrease
–
pads on the unit
or the
Increase
+
/
Decrease
–
pads on the remote control
will set the delay time when using the
Delay 1–24hr
timer. The
Set
light will turn on while setting.
5. Fan Speed Pads
Use to set the fan speed to
Low, Med, High
or
Auto
on the
unit.
NOTE:
On the remote control, use the fan speed
Increase
+
/ Decrease
–
pads to set the fan speeds to
Low, Med
or
High
. Use the
Auto
pad to turn
Auto
fan on.
6. Mode Pad
Use to set the air conditioner to
Cool, Energy Saver
or
Fan
Only
mode.
7. Delay Pads/Delay 1-24hr Pad
'HOD\21³
When the air conditioner is off, it can be set to
automatically come on in 1 to 24 hours at its previous mode
and fan settings.
'HOD\2))³
When the air conditioner is on, it can be set to
automatically turn off in 1 to 24 hours.
How to set:
Press the
Delay 1–24hr
pad on the unit or the
Delay pad
on
the remote control. Each touch of the
Increase
+
/
Decrease
–
pads on the unit or the
Increase
+
/
Decrease
–
pads on the remote control will set the timer in
1-hour intervals. The
Set
light will turn on while setting.
To review the remaining time on the
Delay 1–24hr
timer,
press the
Delay 1–24hr
pad on the unit or the
Delay pad
on
the remote control. Use the
Increase
+
/
Decrease
–
pads on
the unit or the
Increase
+
/
Decrease
–
pads on the remote
control to set a new time if desired.
To cancel the timer,
press the
Delay 1–24hr
pad until the light
on the
Delay 1–24hr
pad goes off.
8.
Filter Check
LED will turn on when fan has accumulated 250 hours of run
time as a reminder to clean filter. Press
Filter Check
to turn off
the LED and reset the accumulated run time.
Note:
The default temperature reading on the display is degree Fahrenheit ( °F). To change the display to degree Celcius (°C), press
the Temp Increase
+
and Temp Decrease
–
buttons together and hold for 3 seconds. Repeat the process to change back to degree
Fahrenheit (°F)
NOTE:
The display always shows the room temperature except
when setting the Set temperature or the Delay timer.
Light indicates the
delay timer is set.
Light indicates the unit is in the
temperature or delay time Set mode.
Remote Control
Set
Filter
Check
Delay
1-24 Hrs
Auto
High
Med
Low
Cool
Fan Only
Energy Saver
-
+
Mode
Fan
Speed
Power
Temp / Delay
8
Summary of Contents for AEZ05 and
Page 12: ...Notes 12...
Page 25: ...Notes GEAppliances com 25...