49-5000634 Rev. 1
5
USING THE
AIR CONDITIONER:
Controls
Controls
Features and appearance will vary.
Lights beside the touch pads on the air conditioner control panel
indicate the selected settings.
Remote Control
Air Conditioner Controls
1. Power Pad
Turns air conditioner on and off. When turned on,
the display will show the set temperature and user
settings.
2. Display
Shows the room temperature or time remaining on the
Delay timer. Shows the
Set
temperature while setting
the temperature in
Cool, Dry
or
Eco
modes.
3. Temp and Delay + /– Pads
8VHWRVHWWHPSHUDWXUHRUGHOD\WLPH7HPSHUDWXUH
can be set in
Cool, Dry
and
Eco
mode.
4. Mode Pad
8VHWRVHWWKHDLUFRQGLWLRQHUWR
Fan Only, Cool, Dry
or
Eco
mode.
5. Fan Speed Pad
In
Cool, Eco or Dry
PRGH8VHWRVHWWKHIDQVSHHG
to
Auto, Quiet, Med, or High
on the unit.
In
Fan
PRGH8VHWRVHWWKHIDQVSHHGWR
High, Med
,
or
Quiet
on the unit.
6. Delay (set by remote control only)
With the
Delay On
feature the unit will operate in
ECO
mode at the set temperature and fan speed.
After pressing
Delay
pad the display will show “- -”.
Pressing the
Delay +
button will increase the hours
by 1 from 24. The
Delay –
button will decrease the
hours by 1 from 24 to 1. When the set delay time has
expired, the unit will turn on as if the
POWER
button
was pressed.
To cancel the Delay function, press the
POWER
button.
7.
Sleep Pad
The
SLEEP
mode sets the unit to gradually change
settings over an 8 hour period to allow for some
increased energy efficiency during sleep hours.
The
SLEEP
mode is available only in
COOL, DRY
and
ECO
mode.
Press the
SLEEP
mode pad and its light will illuminate.
In
SLEEP
mode, the unit will automatically change and
display the fan speed depending on the prior settings.
If fan speed was
High
or
Med
, the unit will decrease
the fan speed by one setting.
If fan speed was
Quiet
or
Auto
, the unit will set the fan
speed as
Quiet
.
The fan will stay the set speed setting for 8 hours from
the time the
SLEEP
mode button was pressed. The
air conditioner will then raise the set point by 2°F after
1 hour and 2°F more after another hour where it will
remain for the next 6 hours. The display will not show
the adjusted set points. During this time, the display
will show “08” at the beginning, representing the 8 hour
run time, and will decrease by 1 with each passing
hour. After 8 hours, the air conditioner will resume the
settings that were in place before the
SLEEP
mode
button was pressed.
While in
SLEEP
mode, pressing the
SLEEP
or
POWER
button will exit
SLEEP
mode. The only other
allowable button in sleep mode is
SPEED
. Any other
button will result in a double beep, confirming an invalid
operation.
8.
Filter Reset Pad
This feature automatically notifies you that the filters
must be cleaned. The indicator light will come on after
250 hours of operation. Clean the filters
(REFER TO
PAGE 7)
, place them back into the unit, and press the
Filter Reset
pad. The light will go off.
9. WiFi Connect Pad
Enables connection of the air conditioner to the home
WiFi. Download App for details at:
www.GEAppliances.com/connect
.
10. Quiet Mode
Sets fan speed to
QUIET
8VHZLWK
COOL, FAN,
ECO
, and
DRY
modes. Can be set on the unit or by
remote control.
Power
Speed
Mode
Quiet
Delay
1
4
6
5
10
3
1
2
7
4
5
9
8
3
Summary of Contents for AHTT06
Page 20: ...20 49 5000634 Rev 1 Notes ...
Page 42: ...20 49 5000634 Rev 1 Notas ...
