REPLACING THE OVEN DOOR
NOTE:
The oven door is heavy. You may need help lifting the door high enough to
slide it into the hinge slots. Do not lift the door by the handle.
A.
Lift the oven door by placing one hand on each side. The door is heavy, so you may
need help. Do not lift the door by the handle.
B.
With the door at the same angle as the removal position (approximately 1"–2"
[2.5 cm–5.1 cm] from the closed position), seat the notch of the hinge arm into the
bottom edge of the hinge slot. The notch of the hinge arm must be fully seated
into the bottom of the slot.
C.
Fully open the door. If the door will not fully open, the indentation is not seated
correctly in the bottom edge of the slot.
D.
Push the hinge locks up against the front frame of the oven cavity, to the locked position.
E.
Close the oven door.
REPLACE THE STORAGE DRAWER
A.
Place the drawer rail on the guides. Push the drawer in until it stops.
B.
Lift the front of the drawer and push in until the stops clear the
guides.
C.
Lower the front of the drawer and push in until it closes.
8
Hinge in locked
position
Notch of hinge
securely fitted
into bottom
of hinge slot
Bottom edge
of slot
Hinge arm
COOKTOP BURNERS (CONT.)
ASSEMBLE THE BURNERS (CONT.)
If you have a metal cooktop, skip to
.
FOR GLASS CERAMIC COOKTOPS
A.
Place burner heads over the electrodes on the
cooktop, in the correct locations according to their
sizes.
B.
Place the matching size caps onto the heads.
Make sure that the heads and caps are placed in the correct locations.
Place the vent cover, grates and air inlet cover onto the cooktop, making sure that the grates
lock the vent cover in place.
C
B
9
Spark
igniter
location
Burner grate
Burner
base
Burner
cap
Burner
head
Spark
igniter
Burner cap
properly seated
Burner cap not
properly seated
COOKTOP BURNERS
ASSEMBLE THE BURNERS
CAUTION:
The electrode of the spark igniter is exposed. Be careful not
to impact the electrode, as damage to the igniter could occur. Be careful not to turn on any
cooktop controls while touching an electrode. A slight electrical shock may occur.
If you have a glass ceramic cooktop, skip to
.
FOR METAL COOKTOPS
A.
Place burner heads over the electrodes on the cooktop, in the correct locations according
to their sizes.
B.
Make sure the slot in the burner head is positioned over the
electrode (on some models).
C.
Place the matching size caps onto the heads.
Make sure that the heads and caps are placed in the correct locations.
Place the vent cover, grates and air inlet cover onto the cooktop, making sure that the grates
lock the vent cover in place.
B
A
9
Medium head
and cap
Large head
and cap
Small head
and cap
Large head
and cap
Front of range
Burner cap
properly seated
Burner cap not
properly seated
COOKTOP BURNERS (CONT.)
CHECK THE IGNITERS
Operation of the electric igniters should be checked after the cooktop and supply line have
been carefully checked for leaks and the cooktop has been connected to the electrical power.
A.
Turn on gas.
B.
Push and turn a burner valve to the LITE position.
•
The burner valve should light when gas is available to the burner.
•
Once the burner lights, it should be turned out of the LITE position.
C.
Try each valve separately until all burners have been checked.
BURNER IGNITION
Cooktop Spark Ignition—When you turn the cooktop knob to LITE, the spark igniter makes
a series of electric sparks (ticking sounds) which light the burner. During a power failure,
the burners will not light automatically. In an emergency, a cooktop burner may be lit with
a match by following the steps below.
WARNING:
Lighting gas burners with a match is dangerous.
You should match light the cooktop burners only in an emergency.
A.
Light a match and hold the flame near the burner you want to light. Wooden matches
work best.
B.
Push in and turn the control knob slowly. Be sure you are turning the correct knob
for the burner you are lighting.
NOTE:
If the burner does not light within 5 seconds, turn the knob off and wait 5 minutes
before trying again.
BURNER FLAMES
Turn each burner on. Turn each burner knob to the high position. Flames should be blue in color with
little or no trace of yellow. The burner flames should not flutter or blow away from the burner. The inner
cone of the flame should be between 1/2" and 3/4" (12.7 mm and 19.1 mm) long. If the burner flames
are yellow in color or not the proper length, call GE Service.
Burners should be checked frequently.
WARNING:
If you attempt to measure the inner cone of the ame,
please use caution. Burns could result.
E
9
D
C
1/2" to 3/4" (12.7 mm to 19.1 mm)
COOKTOP
BURNER
Flames should circle burner
BAKE AND BROIL BURNERS
CHECKING THE OVEN BURNERS
To check the bake burner
with the oven door in the closed position:
A.
Open the door and remove it. (Optional—see Step 4.)
B.
Remove the oven racks.
C.
Remove the oven bottom.
Lift the oven bottom up at the rear and pull forward.
D.
Remove the four screws holding the burner baffle (flame spreader) to the burner box.
E.
Install and close the oven door.
F.
Turn on the bake burner.
The broil burner flames may be seen without removing the racks, oven bottom or bake baffles.
10
A
FINAL INSTALLATION CHECKLIST
•
Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are replaced.
•
Be sure power is in service to the building.
•
Check that all packing materials and tape have been removed. This will include tape on metal
panel under control knobs (if applicable), adhesive tape, wire ties, cardboard and protective plastic.
Failure to remove these materials could result in damage to the appliance once the appliance has
been turned on and surfaces have heated.
•
Check that the door and drawer are parallel to each other and that both operate smoothly. If they
do not, repeat steps 4 and 9.
•
Check to make sure that the rear leveling leg is fully inserted into the anti-tip bracket and that
the bracket is securely installed.
OPERATION CHECKLIST
•
Check that the oven control operates properly. If the oven control does not operate properly,
recheck the wiring connections.
•
Be sure all range controls are in the OFF position before leaving the range.
11
BAKE AND BROIL BURNERS (CONT.)
ADJUST THE AIR SHUTTER
WHAT ADJUSTMENT TO MAKE:
A.
If the flames are yellow, open the air shutter more than
the original setting.
B.
If the flames blow away or flutter from the burner,
close the air shutter more than the original setting.
MAKING THE ADJUSTMENT:
A.
Bake burner: The broil burner is located and accessible
in the top rear of the oven.
B.
Using a screwdriver, loosen the air shutter adjustment
screw.
C.
Make the air shutter adjustment.
D.
Retighten the air shutter screw.
E.
Check the inner cone of the flame. It should be between 1/2" and 3/4"
(12.7 mm and 19.1 mm) long for the oven bake and broil burners.
WHEN ALL ADJUSTMENTS ARE MADE AND THE RESULTS
ARE SATISFACTORY:
A.
Replace the orifice fitting cover.
B.
Replace the burner baffle (flame spreader) and screws.
C.
Replace the oven bottom.
D.
Replace the oven door.
10
B
Air Shut
Adjustment
Air shutter adjustment
screw
Air shutter opening
1/2" TO 3/4"
DE LLAMA
QUEMADOR PARA
HORNEAR/ASAR
Inner cone
of flame
Oven broiler
burner
1/2" to 3/4" (12.7 mm to 19.1 mm)
FLAME
SPREADER
ORIFICE COVER
OVEN BOTTOM
BURNER
