GE Multilin
D30 Line Distance Protection System
6-23
6 ACTUAL VALUES
6.5 PRODUCT INFORMATION
6
6.5PRODUCT INFORMATION
6.5.1 MODEL INFORMATION
PATH: ACTUAL VALUES
PRODUCT INFO
MODEL INFORMATION
The order code, serial number, Ethernet MAC address, date and time of manufacture, and operating time are shown here.
ETHERNET MAC ADDRESS
— UR devices with firmware 7.0x and above have three Ethernet ports that can be used on three
networks. The MAC address displays for port 1. The MAC address for port 2 is one higher. The MAC address for port 3 is
one higher than port 2. In redundant mode, the MAC addresses for ports 2 and 3 are the same as port 2.
6.5.2 FIRMWARE REVISIONS
PATH: ACTUAL VALUES
PRODUCT INFO
FIRMWARE REVISIONS
The shown data is illustrative only. A modification file number of 0 indicates that, currently, no modifications have been
installed.
MODEL INFORMATION
ORDER CODE LINE 1:
D30-E00-HCL-F8H-H6A
Range: standard GE Multilin order code format;
example order code shown
MESSAGE
ORDER CODE LINE 2:
Range: standard GE Multilin order code format
MESSAGE
ORDER CODE LINE 3:
Range: standard GE Multilin order code format
MESSAGE
ORDER CODE LINE 4:
Range: standard GE Multilin order code format
MESSAGE
SERIAL NUMBER:
Range: standard GE Multilin serial number format
MESSAGE
ETHERNET MAC ADDRESS
000000000000
Range: standard Ethernet MAC address format
MESSAGE
MANUFACTURING DATE:
0
Range: YYYY/MM/DD HH:MM:SS
MESSAGE
CT/ VT ADVANCED DIAG
ACTIVE: No
Range: Yes, No
MESSAGE
OPERATING TIME:
0:00:00
Range: operating time in HH:MM:SS
MESSAGE
LAST SETTING CHANGE:
1970/01/01 23:11:19
Range: YYYY/MM/DD HH:MM:SS
FIRMWARE REVISIONS
D30 Line Relay
REVISION: 7.0x
Range: 0.00 to 655.35
Revision number of the application firmware.
MESSAGE
MODIFICATION FILE
NUMBER: 0
Range: 0 to 65535 (ID of the MOD FILE)
Value is 0 for each standard firmware release.
MESSAGE
BOOT PROGRAM
REVISION: 3.01
Range: 0.00 to 655.35
Revision number of the boot program firmware.
MESSAGE
FRONT PANEL PROGRAM
REVISION: 0.08
Range: 0.00 to 655.35
Revision number of faceplate program firmware.
MESSAGE
COMPILE DATE:
2004/09/15 04:55:16
Range: Any valid date and time.
Date and time when product firmware was built.
MESSAGE
BOOT DATE:
2004/09/15 16:41:32
Range: Any valid date and time.
Date and time when the boot program was built.
Summary of Contents for D30D00HCHF8AH6AM6BP8BX7A
