S
TORING
A N
UMBER
I
N
M
EMORY
D
IRECT
M
EMORIES
To store a number in M1-M3.
1. Pick up the handset, press
“
STORE
”
button.
2. Use the number keypad to enter the telephone number
you want to store (up to 16 digits).
3. Press
“
STORE
”
button again.
4. Press a ONE-TOUCH MEMORY button(M1-M3).
5. Put back handset on cradle.
To dial a number stored in M1-M3.
1. Press
“
SPEAKER
”
button or pick up the handset.
2. Press a ONE-TOUCH MEMORY button(M1-M3)
T
WO
T
OUCH
M
EMORIES
To store a number in a Two-touch memory(0-9)
1. Pick up the handset and press the STORE button;
2. Key in the telephone number to be stored.
3. Press the
“
STORE
”
button;
4. Using the dialing keypad, press any button between 0-
9 to enter the memory location.
5. Put back handset on cradle.
To dial a number stored in Two-touch memory (0-9)
1. Pick up the handset or press
“
speakerphone
”
button;
2. Press the
“
DIAL
”
button.
3. Key in the memory location number(0-9);
4. The number will be dialed.
C
HANGING
A S
TORED
N
UMBER
Use the same procedure to change a stored number as
you store a number the you
’
re just replacing the phone
number with a different one.
The new number replaces the old number at the memory
location.
G
ENERAL
P
RODUCT
C
ARE
To keep your telephone working and looking good, follow
these guidelines:
DO NOT expose to direct sunlight or moisture.
Avoid dropping and other rough treatment to the phone.
Clean with a soft cloth.
Never use a strong cleaning agent or abrasive powder
because this will damage the finish.
Retain the original packaging in case you need to ship the
phone at a later date.
T
ELEPHONE
P
roblem
Solution
No dial tone Check installation:
Is the telephone line cord connected
to the base unit and the wall jack?
Disconnect the base from the wall
jack and connect another phone to
the same jack. If there is no dial
tone in the second phone, the prob-
lem might be your wiring or local
service.
Dial tone is OK, Make sure the tone/pulse setting
but can't dial out is correct.
Does not ring
Try to set the Ringer to a higher level.
You may have too many extension
phones on your line. Try unplugging
some phones.
See solutions for No dial tone.
M
EMORY
D
IALING
Did you program the memory location keys correctly?
Did you follow proper dialing sequence?
Make sure the tone/pulse setting is correct.
Model: EX29351
00009112
(Rev.0 E)
06-10
Printed in China
R
ECEIVING
A C
ALL
1. Press the
“
SPEAKER
”
button or pick up the handset to
answer the phone.
2. Press the
“
SPEAKER
”
button again or put the handset
on cradle to hang up.
M
AKING
A C
ALL
To make a call, press the
“
SPEAKER
”
button or pick up
the handset before you dial and press
“
SPEAKER
”
button
again or put the handset on cradle to hang up.
R
EDIAL
To repeat a call to the last number you dialled(up to 32 digit)
1. Press "SPEAKER" button or pick up the handset to get a
dialling tone.
2. Press "REDIAL" button to dial the last number redial.
P
AUSE
Press the
“
PAUSE
”
button when you dial the telephone
number, duing the phone dialing the phone shall pause for
2-4 second.
F
LASH
Use the
“
FLASH
”
button to activate custom calling
services such as call transfer, which are available
through your local telephone company.
Don
’
t use
“
SPEAKER
”
button to activate custom calling
services, or you
’
ll hang up the phone.
M
UTE
To prevent the person you are speaking from hearing you
while on a call.
Press and hold
“
MUTE
”
button.
V
ISUAL
M
ESSAGE
W
AITING
I
NDICATOR
When you connect the phone to an Alcatel PABX, the
VMWI will blink if there has a message in the centralized
voice mail system. You need to contact your services
provider for more details.
M
EMORY
The phone has three one-touch memories,M1 to M3 and
ten two-touch memories, 0 to 9.Each memory location
can have up to 16 digits. You can store part of a number
(e.g. the dialling code) in memory, then use a combina-
tion of memory and manual dialling, in any order,to make
a call.
Warning:
If the phone is disconnected from the telephone
line, any stored numbers while be lost within
1.5 hour. If you want to change a number stored in a memory,
simply store another one over it.
please ignore any tones or recorded messages you may hear
from the network will you are storing number.
Used equipment must be disposed of in compli-
ance with current environmental protection
regulations. You should return it to your reseller or
dispose of it in an approved recycling centre.
Summary of Contents for EX29351
Page 3: ......
