GE F60 UR Series Instruction Manual Download

Page: 150 / 558

5-24

F60 Feeder Protection System

GE Multilin

5.2 PRODUCT SETUP

5 SETTINGS

Configure the data by making the following changes in the

PRODUCT SETUP

ÖØ

COMMUNICATION

ÖØ

IEC 61850 PROTO-

COL

GGIO1 STATUS CONFIGURATION

settings menu:

–

Set

GGIO1 INDICATION 1

to a FlexLogic™ operand used to provide the status of GGIO1.ST.Ind1.stVal (for example,

a contact input, virtual input, a protection element status, etc.).

The F60 must be rebooted (control power removed and re-applied) before these settings take effect.

The following procedure illustrates the reception configuration.

Configure the reception dataset by making the following changes in the

PRODUCT SETUP

ÖØ

COMMUNICATION

ÖØ

IEC

61850 PROTOCOL

GSSE/GOOSE CONFIGURATION

ÖØ

RECEPTION

ÖØ

CONFIGURABLE GOOSE

ÖØ

CONFIG GSE 1 DATASET ITEMS

settings menu:

–

Set

ITEM 1

to “GGIO3.ST.Ind1.q” to indicate quality flags for GGIO3 status indication 1.

–

Set

ITEM 2

to “GGIO3.ST.Ind1.stVal” to indicate the status value for GGIO3 status indication 1.

The reception dataset now contains a set of quality flags, a single point status Boolean value, and a floating point ana-
log value. This matches the transmission dataset configuration above.

Configure the GOOSE service settings by making the following changes in the

INPUTS/OUTPUTS

ÖØ

REMOTE DEVICES

ÖØ

REMOTE DEVICE 1

settings menu:

–

Set

REMOTE DEVICE 1 ID

to match the GOOSE ID string for the transmitting device. Enter “GOOSEOut_1”.

–

Set

REMOTE DEVICE 1 ETYPE APPID

to match the ETHERTYPE application ID from the transmitting device. This is

“0” in the example above.

–

Set the

REMOTE DEVICE 1 DATASET

value. This value represents the dataset number in use. Since we are using

configurable GOOSE 1 in this example, program this value as “GOOSEIn 1”.

Configure the data by making the following changes in the

INPUTS/OUTPUTS

ÖØ

REMOTE INPUTS

ÖØ

REMOTE INPUT 1

settings menu:

–

Set

REMOTE IN 1 DEVICE

to “GOOSEOut_1”.

–

Set

REMOTE IN 1 ITEM

to “Dataset Item 2”. This assigns the value of the GGIO3.ST.Ind1.stVal single point status

item to remote input 1.

Remote input 1 can now be used in FlexLogic™ equations or other settings. The F60 must be rebooted (control power
removed and re-applied) before these settings take effect.

The value of remote input 1 (Boolean on or off) in the receiving device will be determined by the GGIO1.ST.Ind1.stVal value
in the sending device. The above settings will be automatically populated by the EnerVista UR Setup software when a com-
plete SCD file is created by third party substation configurator software.

For intercommunication between F60 IEDs, the fixed (DNA/UserSt) dataset can be used. The DNA/UserSt dataset contains
the same DNA and UserSt bit pairs that are included in GSSE messages. All GOOSE messages transmitted by the F60
(DNA/UserSt dataset and configurable datasets) use the IEC 61850 GOOSE messaging services (for example, VLAN sup-
port).

Set the

CONFIG GSE 1 FUNCTION

function to “Disabled” when configuration changes are required. Once changes are

entered, return the

CONFIG GSE 1 FUNCTION

to “Enabled” and restart the unit for changes to take effect.

PATH:...TRANSMISSION

ÖØ

CONFIGURABLE GOOSE 1(8)

ÖØ

CONIFIG GSE 1(64) DATA TIMES

ITEM 1(64)

To create a configurable GOOSE dataset that contains an IEC 61850 Single Point Status indication and its associated qual-
ity flags, the following dataset items can be selected: “GGIO1.ST.Ind1.stVal” and “GGIO1.ST.Ind1.q”. The F60 will then cre-
ate a dataset containing these two data items. The status value for GGIO1.ST.Ind1.stVal is determined by the FlexLogic™
operand assigned to GGIO1 indication 1. Changes to this operand will result in the transmission of GOOSE messages con-
taining the defined dataset.

CONFIG GSE 1

DATASET ITEMS

ITEM 1:

GGIO1.ST.Ind1.stVal

Range: all valid MMS data item references for

transmitted data

NOTE