20
49-90587
TROUBLESHOOTING TIPS
Troubleshooting Tips...
Before you call for service
Problem
Possible Causes
What To Do
Clothes too wet
Incorrect cycle selected
Make sure the cycle selected matches the load you are washing.
Some fabrics will feel wetter when rinsed with cold water.
Wash load out of balance
Redistribute load in washer and run through
Spin
cycle.
Blinking Spin light
or Spin light on at
end of cycle
Out of balance
condition has been
detected
Allow cycle to continue and finish.
If load is wet at the end of the cycle, even out load and run a
Spin
cycle.
Pilling
Result of normal wear on
poly-cotton blends and
fuzzy fabrics
While this is not caused by the washer, you can slow the pilling
process by washing garments inside out.
Snags, holes, tears,
rips or excessive
wear
Pins, snaps, hooks,
sharp buttons, belt
buckles, zippers and
sharp objects left in
pockets
Fasten snaps, hooks, buttons and zippers.
Remove loose items like pins, objects in pockets and sharp
buttons.
Turn knits (which snag easily) inside out.
Undiluted chlorine
bleach
Check bleach package instructions for proper amount.
Never add undiluted bleach to wash or allow clothes to come in
contact with undiluted bleach.
Chemicals like hair
bleach or dye, permanent
wave solution
Rinse items that may have chemicals on them before washing.
Use
Speed Wash
cycle with
Extra Rinse
option.
Wrinkling
Incorrect wash and dry
cycles
Match Cycle selection to the type of fabric you are washing
(especially for easy care loads).
Improper sorting
Avoid mixing heavy items (like jeans) with light items (like blouses).
Try a fabric softener.
Overloading
Loosely load clothes in the washer basket.
Repeated washing in
water that is too hot
Wash in warm or cold water.
Sounds
Possible Causes
Reason
“Clicking”
Shifter mechanism is
engaging or disengaging
The drive system will engage at the start of agitate and disengage
when agitate is complete. This occurs multiple times during the
wash.
Back and forth
“swoosh”
Electric motor reversing
direction
This sound is the motor rotating back and forth to clean your
laundry.
“Clicking” behind
Control during fill
Automatic Temperature
Control Valve
Two valves mix cold and hot water. The “clicking” is when either
valve turns on or off to raise or lower the fill water temperature.
Water flow changes
during fill
Automatic Temperature
Control Valve
Two valves mix cold and hot water. The “clicking” is when either
valve turns on or off to raise or lower the fill water temperature.
Motor sounds during
spin
Motor ramping up/down
during spin cycle
The motor will speed up incrementally during the spin cycle.
When spin is complete, it will coast until it stops.
“Humming”
Water drain pump
The drain pump will make a humming sound when pumping out
water after agitation stops and continue until spin is complete.
Drive motor
The drive motor will make a “humming” sound during the wash and
spin phases of the cycle.
“Gurgling”
Water drain pump
When the pump starts drawing in air, It starts to gurgle. The washer
should then begin spinning and the sound will continue until it is
done spinning.
Water “swishing”
Washing process
Water swishing while the unit is agitating is normal, especially with
smaller loads.
Washer rocking/
moving and/or
“knocking/tapping”
Washer leveling legs
uneven
To level the washer, adjust the leveling legs by rotating the
individual leg in the proper direction for up or down.
“Squeaking” sound
Washer not level and
rubbing on cabinet
To level the washer, adjust the leveling legs by rotating the
individual leg in the proper direction for up or down.
Summary of Contents for GNW128P
