8
49-90587
Getting started
USING THE W
ASHER
Cycle Options
Extra Spin
Set this option to increase the spin time of the cycle.
Pre-Soak
Select the
Pre-Soak
feature to add a soak step following the fill portion of the cycle.
Extra Rinse
When you use extra detergent or bleach to clean heavily soiled clothes, use the
Extra Rinse
option to better remove additional
residues.
Deep Fill
Select the
Deep Fill
feature for loads where extra water is needed.
The
Deep Fill
feature is recommended for special case
loads only, not for typical use.
NOTE:
This option is not allowed for some cycles.
Deep Rinse
Set this option to provide a deep rinse
or when using fabric softener.
H
I
Settings
Individual settings for agitation (
Soil
), water temperature (
Temp
), and spin (
Extra Spin
) can be set from the minimum (lowest
in column) to maximum (highest in column). In general, the higher up the column, the more washer energy will be used.
NOTE:
Extra Spin
typically reduces dryer time/energy usage (i.e. reduces total energy when using both a washer and a dryer).
E
Delay Wash
Press
Delay Wash
to choose the number of hours you want to delay the start of the cycle, and then press
Start/Pause
.
The washer will count down and start automatically at the correct time.
F
Signal
To turn the signal sounds on/off, press
Signal
.
G
Control Lock
Use the control lock before or during a cycle to prevent any selections from being made.
To lock/unlock the washer controls,
press and hold the
Signal
and
Delay Wash
buttons for 3 seconds.
J
Process
Choose the wash processes to include in the cycle. Press
Process
until all the processes you want to include are lit. More than
one process can be selected.
Soak
Select to set a soak process only. Washer basket will fill, soak, and drain.
Wash
Select to set a wash process only. Washer basket will fill, wash, and drain.
Rinse
Select to set a rinse process only. Washer basket will rinse and spin.
Spin
Select to set a spin process only. Washer basket will spin.
Your washer is equipped with Consumer Help Indicator (CHI). CHI is our way to communicate a simple remedy for some situations
that you can perform without the need to call for service. The chart below describes the helpful messages you may notice on your
display when you return to start another load. These messages will provide simple remedies you can quickly perform.
Spin
light
blinking
If an out-of-balance condition is detected by the washer, the
Spin
light will blink during the remaining portion of
the cycle and will stay illuminated for a short time after cycle completion. When this occurs, the washer is taking
actions to correct the out-of-balance condition and complete the cycle normally. In some cases, the washer may
not be able to balance the load and spin up to full speed. If you notice the load is more wet than normal at the end of
the cycle, redistribute the load evenly in the wash basket and run a
Spin
cycle. To run a
Spin
cycle, select the
Normal
cycle and press the
Process
button until only the
Spin
light is on.
Check your house water supply. Did you forget to turn on one or both supply valves after installation or coming
back from vacation?
Indicates the lid is open. Close the lid.
Indicates the laundry load is unbalanced. Reposition laundry evenly in basket, and ensure washer is level.
Indicates water has reached a critical level. Turn off water and power to the washer and call service.
Consumer Help Indicator
Summary of Contents for GNW128P
