background image

9

Installation Instructions

CONNECTING AN ELECTRIC DRYER 

(Skip for gas dryers and if your dryer already has a power cord attached)

Before making the electrical connection, turn off 

the circuit breaker(s) or remove the dryer’s circuit 

fuse(s) at the electrical box. Be sure the dryer 

cord is unplugged from the wall. 

NEVER LEAVE 

THE ACCESS COVER OFF THE TERMINAL 

BLOCK.

MATERIALS YOU WILL NEED

  4” dia. metal elbow

   3/4” Strain relief  

(UL recognized)

   4” Duct clamps (2) or 

4” spring clamps (2)

  Safety glasses

  4” dia. metal duct 

(recommended)

 Gloves

  Exhaust hood

  Duct tape

TOOLS YOU WILL NEED

  Slip-joint pliers

 Level

  4” dia., UL-listed 

flexible metal duct  

(if needed)

  Dryer power cord kit 

(not provided with 

dryer)

UL rated 120/240V, 

30A with 3 or 4 prongs. 

Identify the plug type 

as per the house 

receptacle before 

purchasing line cord.

 Flat-blade 

screwdriver

 Phillips 

screwdriver

  4” Cover Plate  

(Kit WE49X22606)  

(if needed)

POWER CORDS

GE Appliances strongly recommends the use of 

factory specified parts. Select the power cord to fit your 

installation requirements.
Order on-line at 

GEApplianceparts.com

, 24 hours 

a day or by phone at

 877.959.8688

 during normal 

business hours.

Part Number

Type

Length

Amperage

WX9X2

3-Prong

4 Feet

30

WX9X3

3-Prong

5 Feet

30

WX9X4

3-Prong

6 Feet

30

WX9X18

4-Prong

4 Feet

30

WX9X19

4-Prong

5 Feet

30

WX9X20

4-Prong

6 Feet

30

Summary of Contents for GTD72EBPN0DG





















Reviews: