IMPORTANT!
Read Carefully
Keep for future use
7.5 ft. / 2.29 m Pre-Lit Christmas Tree
Nicolas Holiday Inc. thanks you for your purchase of this pre-lit Christmas tree.
With proper use and care, your tree will provide years of use and memories.
Carefully follow the instructions below on how to assemble and disassemble
your tree. If you should have any problems with your tree, or if the tree does
not light after assembly, DO NOT return it to the place of purchase. Please
refer to the trouble shooting section of this manual or call our toll free number:
1-877-398-7337
and a customer service representative will assist you. Our
customer service center is open Monday through Friday 10:00 AM to 7:00
PM EST with additional hours throughout the holiday season. You can also
visit us on the web at:
Enjoy your holidays!
Before you Begin:
The tree needs to be placed in a clear area, on a flat surface with no obstructions.
Remove and unwrap all parts. Retain shipping carton for future storage.
Preassembly:
e)
Refer to the iTwinkle TREE™ Assembly Diagram.
f)
Loosen thumbscrew in stand for legs to open and pole to insert.
g)
Place stand where desired as assembled tree is heavy to move.
Disclaimer:
DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS
LIGHTING OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB
SOCKET. DOING THIS MAY RESULT IN DAMAGE TO YOUR CHRISTMAS
TREE OR CAUSE PERSONAL INJURY. DOING THIS, WILL RESULT IN A
VOID OF THE LIMITED WARRANTY OF THIS PRODUCT.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
▪ this device may not cause harmful interference, and
▪ this device must accept any interference received, including interference that
may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any Changes or Modifications not expressly approved by the
party responsible for compliance could void user’s authority to operate this
equipment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
TM
Tree Assembly Diagram
If needed, adjust branch tips to make the tree look fuller.
Congratulations!
Your lighted tree is complete and ready to use with your
selected device.
Trouble shooting Tips:
If tree does not illuminate, the tree may be plugged into a controlled
wall outlet. Make sure the switch is turned ON. If a tree section does
not light, check:
Sections A, B or Treetop: Recheck all factory and your assembly
connections.
If a portion of a section does not light, check for loose lamps or
missing mini lamps or fuses. Check that the connector on the plug
adapter is fully secured.
NOTES:
The LED reflectors are not removable.
The LED are not replaceable.
Most Frequently Asked Questions
Q. May I add a lighted decorative tree top to my tree?
A. Yes, There is an outlet at the back of the bladed plug of the tree
top.
Q. May I put blinking or flashing bulbs on my tree?
A. No
Q. May I add extra string sets to my pre-lit tree?
A. No
Q. May I put my pre-lit tree outside?
A. No. Pre-lit trees are for indoor use only.
Q. May I hang glass ornaments on a pre-lit tree?
A. Yes, however do not hang directly on the wires of the lights.
Q. May I remove a light string bulb and add a pig tailed illuminated
or animated ornament or motor?
A. No, removing the bulbs and inserting any additional device into
lamp holder will cause the light set to cease to operate and
may revoke the limited warranty of this product.
Tree Storage:
Remove the plug from the wall outlet. Starting from the treetop, first remove
the plug from the extension cord in section B. Then untwist the securing
cap to pull apart the connectors. Lift the treetop straight up from section B.
Step A: Gently and carefully fold the branches up toward the center
to avoid bulb damage
. Place the treetop into your original shipping carton.
Next remove the plug from section B to section A. Set aside after repeating
Step A
. Then while holding the tree pole of section A, loosen the thumb
screw located on the tree stand. Remove section A from the tree stand.
Repeat
Step A
and place into the carton. To close the tree stand for
storage, remove the speaker, loosen thumbscrew and push the legs
inward. Place tree stand and section B into the carton. Place the speaker
into the carton. Seal the carton closed.
Important:
Store your carton neatly in a cool, dry location protected from
sunlight to prolong the tree life and keep the light sets in working order.
Spare Parts:
Your Tree includes a plastic bag containing spare steady and
fuse bulbs, spare 3-amp fuses, as replacements for the lighting strings and
(1) 5-amp fuse.
NOTE:
The 5-amp spare fuse is ONLY to replace an open fuse in the
SHORT extension cord WITHIN the tree section. The spare 7 amp fuse for
the LONG extension cord at the BOTTOM of your tree is located within the
plug cavity.
Item Number: 00684 / 00684D
5.
Untie the
RED
twist-tie to release
the branch panels.
Follow step 2.
3.
Assemble the middle
section after first
removing the green
protective cap.
NOTE:
On a bottom
branch near the pole is
a special male LED
connector. See insert at
top.
2.
Untie the
RED
twist-tie releasing
the branches. All
branches should
fall into place with
a gentle pull on
the outer layer of
branches.
NOTE:
On a top
branch near the
pole is a special
female LED
Connector.
See insert at top
.
6.
Holding the treetop
with one hand gently
pull down the outer
layer of branches. Then
align the treetop post to
the top of the middle
section and insert fully.
(See picture to left)
.
1.
Open the tree stand. Remove the protective
red cap from the bottom section, insert pole
into the stand and tighten the screw.
NOTE:
Unpack and place the speaker on
the stand’s bracket. Hold until Step 8.
7
.
a) Insert the plug from the
treetop into the unused
outlet on extension cord
of the middle section.
b) Align the 3 prongs and flat
area. Fully insert the
LED connectors
together. Twist cap fully
to secure.
4.
a) Insert the plug from
extension cord of the
middle section into
the unused outlet on
extension cord of the
bottom section.
b) Align the 3 prongs
and flat
area. Fully
insert the LED
connectors together.
Twist cap fully
to
secure.
8.
Insert the plug from the
Note in Step
1
directly
into an electrical wall
outlet to turn the tree
lights on.
Wall
Outlet
Speaker
