GE JKD910 Owner'S Manual Download

Page: 14 / 20

Installation of the warming drawer.

Read these instructions completely and carefully.

Installation Below Wall Ovens

■

When installed, the front face of the warming
drawer will be nearly flush with cabinetry doors
or drawer fronts.

■

Drawer overlaps will conceal cut edges on all
sides of the opening.

The rough opening for the drawer must be:

—Depth:

⁄

″

minimum from inside back to

front of cabinet frame.

—Width:

⁄

″

for 27

″

wide models

⁄

″

for 30

″

wide models.

—Height:

⁄

″

—

Allow 2

″

minimum between oven and drawer

cutouts for clearance of overlaps.

NOTE:

If you are installing in frameless cabinets,

it may be necessary to install 1/2

″

wide cleats to

accept drawer mounting screws. See drawer to
find exact locations of mounting screws.

When installed under a wall oven:

Warming drawers are suitable for installation
below only certain specified wall oven models.
See the label attached to the top of the warming
drawer for suitable models.

NOTE:

Electrical receptacle can be installed

as shown for countertop installations. Do not
install receptacle above the top of the warming
drawer cutout.

⁄

″

Min.

2x2 or 2x4 anti-tip
block against rear
wall 9” from floor
to bottom of block

″

Min. above toekick or adjust

to oven installation height

Oven

cutout

NOTE:

Additional clearance between cutouts may

be required. Check to be sure that oven supports
above the warming drawer location do not obstruct
the required interior 23

⁄

″

depth and 9

⁄

″

height.

Installation below a single oven

″

Min

″

Min. above toekick

NOTE:

Additional clearance between cutouts may

be required. Check to be sure that oven supports
above the warming drawer location do not obstruct
the required interior 23

⁄

″

depth and 9

⁄

″

height.

Installation below a double oven

Dimension A

Dimension B

″

Drawer

⁄

″

⁄

″

Drawer

⁄

″

2x2 or 2x4 anti-tip
block against rear
wall 9” from floor
to bottom of block

″

Min.

Allow 5/8”
overlap on
all sides

⁄

″

⁄

″

Min.

Allow 5/8

″

overlap

on all sides

Oven

cutout

⁄

″

⁄

″

⁄

″

⁄

″

⁄

″

Customer Service

Troubleshooting T

ips

Installation Instructions

Care and Cleaning

Operating Instructions

Safety Instructions

Summary of Contents for JKD910





















Search results

Summary of Contents for JKD910

Reviews:

Related manuals for JKD910

Brands by name

Popular brands

GE JKD910, Owner'S Manual

Search results

Summary of Contents for JKD910

Reviews:

Related manuals for JKD910

Brands by name

Popular brands