GE Power Management
469 Motor Management Relay
5-29
5 ACTUAL VALUES
5.8 DIAGNOSTICS
5
•
PLEASE ENTER A NON-ZERO PASSCODE
: If the passcode is zero, the passcode security feature is disabled. If
the Change Passcode Setpoint is entered as yes, this flash message will appear prompting the user to
enter a non-zero passcode which in turn will enable the feature.
•
SETPOINT ACCESS IS NOW PERMITTED:
This flash message notifies the user that setpoints may now be
altered and stored any time the passcode security feature is enabled and a valid passcode is entered.
•
SETPOINT ACCESS IS NOW RESTRICTED:
This message appears if the passcode security feature is enabled, a
valid passcode has been entered, and the
S1 469 SETUP / PASSCODE / SETPOINT ACCESS
setpoint value is
Restricted
. This message also appears anytime that setpoint access is permitted and the access jumper is
removed.
•
DATE ENTRY WAS NOT COMPLETE:
Since the
DATE
setpoint has a special format (MM/DD/YYYY), if
is
pressed before the complete value is entered, this message appears and the new value is not stored.
Another attempt will have to be made with the complete information.
•
DATE ENTRY WAS OUT OF RANGE:
This message appears if and invalid entry is made for the
DATE
(e.g. 15
entered for month).
•
TIME ENTRY WAS NOT COMPLETE
: Since the
TIME
setpoint has a special format (HH/MM/SS.S), if
is
pressed before the complete value entered, this message appears and the new value is not stored.
Another attempt will have to be made with the complete information.
•
TIME ENTRY WAS OUT OF RANGE:
If and invalid entry is made for the time (e.g. 35 entered for hour), this mes-
sage will appear.
•
NO TRIPS OR ALARMS TO RESET:
If
is pressed when there are no trips or alarms present, this mes-
sage will appear.
•
RESET PERFORMED SUCCESSFULLY:
If all trip and alarm features that are active can be cleared (i.e. the condi-
tions that caused these trips and/or alarms are no longer present), then this message will appear when a
RESET is performed, indicating that all trips and alarms have been cleared.
•
ALL POSSIBLE RESETS HAVE BEEN PERFORMED:
If only some of the trip and alarm features that are active can
be cleared (i.e. the conditions that caused some of these trips and/or alarms are still present), then this
message will appear when a RESET is performed, indicating that only trips and alarms that could be reset
have been reset.
•
CONDITION IS PRESENT RESET NOT POSSIBLE:
If no trip and alarm features that are active can be cleared (i.e.
the condition that caused these trips/alarms is still present), then this message appears when
is
pressed.
•
ARE YOU SURE? PRESS [ENTER] TO VERIFY:
If the
key is pressed and resetting of any trip or alarm fea-
ture is possible, this message will appear to ask for verification of the operation. If
is pressed again
while the message is still on the display, the reset will be performed.
•
PRESS [ENTER] TO ADD DEFAULT MESSAGE:
If the
key is pressed anywhere in the 469 actual value
message structure, this message prompts the user to press
to add a new default message. To add
a new default message,
must be pressed while this message is being displayed.
•
DEFAULT MESSAGE HAS BEEN ADDED:
Any time a new default message is added to the default message list,
this message will appear as verification.
•
DEFAULT MESSAGE LIST IS FULL:
If an attempt is made to add a new default message to the default message
list when 20 messages are already assigned, this message will appear. In order to add a message, one of
the existing messages must be removed.
•
PRESS [ENTER] TO REMOVE MESSAGE:
If the decimal key is pressed in the
S1 469 SETUP \ DEFAULT MESSAGES
group, immediately followed by the
key, this message prompts the user to press
to remove
a default message. To remove the default message,
must be pressed while this message is being
displayed.
ENTER
ENTER
RESET
RESET
RESET
RESET
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
