background image

OPM_NPE_XXX_2K0_4K0_1GB_V040

19

NetPro 2000-4000: user manual 4.0 (GB)

GE Digital Energy 

g

NetPro model

:

2000

3000

4000

Ratings

Voltage Amperes (VA)

:

2000

3000

4000

with computer type load
Watts (W)

:

1200

1800

2400

with resistive load
Input thermal circuit breaker (A)

:

10

14

16

Input converter

AC input voltage

:

220 - 240 V

AC input voltage range

:

100% load: 187 - 264 V
  60% load: 160 - 264 V
  30% load: 125 - 264 V

Maximum start-up AC voltage

:

255 V (at any load)

Minimum start-up AC voltage

:

187 V (at any load)

Input current waveform

:

sinusoidal

Input power factor

:

1

Input frequency range

:

50 or 60 Hz ± 10%

Input current (A)

:

6.6

10.0

13.5

Output converter

AC output voltage

:

220/230/240 V (selectable)

AC output voltage tolerance

:

± 1%

Output frequency

:

50 or 60 Hz ± 0.15% unless synchronized to the mains

Output waveform

:

sine wave

Harmonic distortion

:

< 2% (typical 1.5%) with linear load

Power factor

:

0.6

Crest factor (peak to RMS current)

:

up to 6:1

Capacity appliance outlets

:

max. 10 A per outlet

Bypass

AC input voltage range

:

187 - 264 V

Frequency tracking rate

:

max. 2 or 10 Hz/sec.(selectable, factory setting 10Hz/sec)

Frequency tracking rate

:

2 Hz/sec

10 Hz/sec

Frequency tracking range

:

nominal ± 2%

nominal ± 10%

Phase difference

:

< 7°

< 10°

Transfer time

:

< 1 msec.

Overload capability

The UPS is fully protected against overload
Overload behaviour:
on-line operation, bypass enabled 

:

110% during 5 minutes, 150% during 2 seconds

on-line operation, bypass disabled

:

110% during 110 seconds

battery operation, NP2000

:

110% during 5 minutes, >135% during 110 seconds

battery operation, NP3000/4000

:

>110% during 110 seconds

bypass operation

:

depends on rating of thermal circuit breaker; typical

:

105% of TCB value: no trip
135% of TCB value: trip within 1 hour
200% of TCB value: for 2 - 30 secs
300% of TCB value: for 0.8 - 4 secs.

Batteries (ratings given for 25°C)

Nominal voltage (V)

:

72

108

120

Number of 7 Ah batteries

:

  6

  9

10

Type

:

sealed and maintenance free

Service life

:

3 - 6 years (depending on use)

Battery recharge current

:

1.5 A

Battery recharge time

:

2 - 6 hours for 80% capacity, std. battery

Automatic battery test

:

see 3.6.4

Runtime in minutes
at typical load (75%)

:

7

7

7

  Watts

60

190

270

310

120

117

165

185

240

60

95

105

360

38

63

72

600

21

35

40

900

13

22

25

1200

9

15

18

1800

-

9

10

General

Weight (kg)

:

27

38

42

Dimensions (hxwxd, mm)

:

293x220x557

Enclosure / protection

:

steel-plastic / IP20

Environment

Safety

:

EN 50091-1-1; EN 60950; IEC 950

Electromagnetic compatibility

:

EN 50091-2; EN 50081-1 + EN 50082-1; IEC 801-5: 6kV

Ambient temperature

:

-10 to +40°C

Audible noise at 1 meter

:

45 dB(A)
The audible noise is load and temperature dependent

Max. relative humidity

:

95% (non-condensing)

8  -  Specifications

Summary of Contents for NetPro Series





















Reviews: