background image

Safety Information

2

CONTENTS

Design Information

Models Available......................................................................2
Product Dimensions and Clearances ............................3
Tools and Parts Required ....................................................3
Parts Supplied ..........................................................................3
Electrical Tools and Parts Required ................................3
Advance Planning ..................................................................3

Installation Preparation

Electrical Requirements........................................................4
Install Junction Box ................................................................4
Preparing the Opening (Installation without

an accessory storage drawer)..................................5-6

Preparing the Opening (Installation with

an accessory storage drawer)..................................7-8

Installation Instructions

Step 1, Remove Packaging and Parts ..........................9
Step 2, Route Conduit ........................................................10
Step 3, Install Bottom Trim ..............................................11
Step 4, Install Mounting Screws ....................................11
Step 5, Finalize Installation ..............................................11

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT

Save these instructions for

local inspector’s use. 

IMPORTANT

Observe all governing codes

and ordinances.

Note to Installer

Be sure to leave these

instructions with the Consumer.

Note to Consumer

Keep these instructions 

with your Owner’s Manual for future reference.

Skill Level

Installation of this appliance

requires basic mechanical and electrical skills.

Completion Time

1 Hour.

• 

Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the warranty.
See Owner’s Manual for warranty information.

IMPORTANT

Use this oven only for 

its intended purpose. Never use the oven for
warming or heating a room. Prolonged use of the
oven without proper ventilation can be hazardous.

CAUTION:

For personal safety, remove house fuse or oven
circuit breaker before beginning installation to
avoid severe or fatal shock injury.

CAUTION:

For personal safety, the mounting surface must 
be capable of supporting the cabinet load, in
addition to the added weight of the 80-pound oven
and 30-pound drawer, plus additional oven loads of
up to 50 pounds or a total weight of up to 160
pounds.

CAUTION:

For personal safety, this product cannot be
installed in cabinet arrangements such as an 
island, a peninsula or below a countertop.

MODELS AVAILABLE

Profile Models:

PSB2200NWW–White
PSB2200NBB–Black
PSB2201NSS–Stainless Steel

Monogram Models:

ZSC2200NWW–White 
ZSC2200NBB–Black
ZSC2201NSS–Stainless Steel

Monogram Pro Range Models:

ZSC2202NSS–Stainless Steel

NOTE: This unit cannot be installed with an
accessory storage drawer.

Summary of Contents for Profile Advantium PSB2200

















Reviews: