GE Profile Owner'S Manual And Installation Instructions Download

Page: 1 / 46

GEAppliances.com

Refrigerators

Bottom Freezer

239D4106P020 49-60716-5 10-15 GE

Safety Instructions

. . . . . . . . . . . .2, 3

Operating Instructions

Features . . . . . . . . . . . . . . . . . . . . . . . . . .4, 5

Controls . . . . . . . . . . . . . . . . . . . . . . . . . .6–9

Dispenser* . . . . . . . . . . . . . . . . . . . . . . . . .10

Autofill* . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

About Appliance Communication . . .12

Water Filter . . . . . . . . . . . . . . . . . . . . . . . .13

Fresh Food Storage Options . . . . .14,15

Climate Zone & Temperature

Controlled Drawer . . . . . . . . . . . . . . .16,17

Freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Automatic Ice maker . . . . . . . . . . . . . . .19

Care and Cleaning . . . . . . . . . . . . . . . . 20

Replacing the Lights . . . . . . . . . . . . . . . .21

Installation Instructions

Preparing to Install the

Refrigerator . . . . . . . . . . . . . . . . . . . . 22, 23

Installing the Refrigerator . . . . . . . 24-34

Installing the Water Line . . . . . . . . 35-37

Troubleshooting Tips

. . . . . . 39, 40

Normal Operating Conditions . . . . . . .38

Truth or Myth . . . . . . . . . . . . . . . . . . 41, 42

Consumer Support

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .42

RPWFE Water Filter Cartridge Limited

Warranty . . . . . . . . . . . . . . . . . . . . . . . . .44

Performance Data Sheet . . . . . . . . . . .45

Consumer Support . . . . . . . . Back Cover

Write the model and serial
numbers here:

Model # ____________________

Serial # ____________________

Find these numbers on a label
on the left side, near the middle
of the refrigerator compartment.

GE and GE Profile™ models

Models that start with PFE, GFE, DFE, PFH,

and GNE are Standard Depth Models (SD)

Models that start with GYE, PYE and PWE

are Counter Depth Models (CD)

Owner’s Manual and

Installation Instructions

*Select Models Only

Modèles GE et GE Profile™

Manuel d’utilisation

et instructions

d’installation

Les numéros de modèle commençant par PFE, GFE,

DFE, PFH, et GNE sont des modèles

de profondeur normale (PN).

Les numéros de modèle commençant par GYE, PYE

et PWE sont des modèles de profondeur

de comptoir (PC).

Réfrigérateurs

GE y GE Profile™ modelos

Manual del Propietario e

Instrucciones de Instalación

Los modelos que comienzan con las letras

PFE, GFE, DFE, PFH, y GNE son Modelos con

Profundidad Estándar (SD)

Los modelos que comienzan con las

letras GYE, PYE y PWE son Modelos con

Profundidad de Mesada (CD)

Refrigeradores

La section française commence à la

page 47

La sección en español empieza en la

página 91

Summary of Contents for Profile















































Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands

GE Profile, Owner'S Manual And Installation Instructions

Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands