background image

Installation Instructions

6

Appliance dimensions

Power Requirements

The outlet must be properly grounded in accordance with 

all applicable codes.

It can be installed inside the cabinet above the appliance.

Electrical Installation

Electrical Requirements:

• 

a three prong grounded outlet

• 

120 V, 60 Hz, AC only

• 

20 Amp electrical supply with a fuse or a circuit breaker

This product must be connected to a supply circuit of the 

proper voltage and frequency. Wire size must conform to the 

requirements of the National Electric Code or the prevailing 

local code for this rating. The power supply cord and plug 

should be brought to a separate 20-amp branch circuit 

single grounded outlet. The outlet box should be located 

inside the cabinet above the appliance (see section Location 

Requirements). The outlet box and supply circuit should be 

installed by a qualified electrician and conform to the National 

Electrical Code or the prevailing local code.
The voltage used must be the same as specified on this 

microwave oven. Using a higher voltage is dangerous and 

may result in a fire or oven damage. Using a lower voltage 

will cause slow cooking. The dealer is not responsible for any 

damages resulting from the use of the oven with any voltage 

other than specified.

29-7/8" 

(760mm)

15-3/8" 

(390mm)

16-1/2" 

(419mm)

Summary of Contents for PVM1899















Reviews: