GE SG 300 Installation Manual Download

Page: 32 / 40

3.9.2 Parallel control bus connection

In cases of parallel operation, the communication between the units takes place through the

control

bus cables

Each parallel unit is equipped with an additional board “

P13

–

RPA Board

“

where the connectors

J52

(A)

and

J62

(B)

are located.

A short control cable provided with a ferrite ring core links the parallel board “

P13 – RPA Board

”

with the

parallel bus socket on which must be connected the

control bus cables

and

on PCB

“

P34 – Bus

Interface

”

All the parallel units are connected to the same control bus.

This connection allows:

•

The microprocessors of each unit to communicate with each other.

•

The oscillators of each unit to be locked together.

•

The regulation loops to compare the output current of each unit in order to equally share the load
current.

For increased reliability, this connection is made with redundant cables.
In this way, communication is maintained between units in case one of the control cables should fail or
be accidentally damaged or disconnected.

The standard length of the control bus cable between two parallel unit is

40 ft

12 m

Maximal overall length of bus connection, between the first and the last unit, should not be longer than

276 ft

84 m

Verify that control wiring is run in individual separate steel conduit.

NOTE !

Under no circumstance should the control bus cable connecting

(1/2/3/4/5)

and

JB (1/2/3/4/5)

be connected or disconnected after the system has been powered On.

JP3

JP2

JP1

JP4

IM 0048

JB1

JA1

JP3

JP4

JP2

JP1

-300

2_R

-IM

004

8_01

JB1

JP1

JP2

JP4

JP3

JA1

JB2

JA2

JB2
JB3

JA2
JA3

JP1

JP2

JP4

JP3

JA2 + JB2

JA1 + JB1

JA3 + JB3

Next parallel
unit 4, 5, 6

UPS 1

UPS 2

UPS 3

JP3

JP1

JP4

IM 0048

JP2

JP3

JP1

JP4

IM 0048

Fig. 3.9.2-1 RPA System - Control bus connection

The shield of the control bus cable, connected on

and

must be connected to ground with the

appropriate cable clamps fitted on parallel bus socket.

It is important to place the units in sequence of their assigned number.

A unit number from

, is defined by the setting of parameters and displayed on the panel.

This number is also marked inside and outside the packaging.

Modifications reserved

Page 32/40

OPM_SGS_ISG_M22_M30_2US_V010.doc

Installation Guide

SG Series 225 & 300 UL S2

Summary of Contents for SG 300









































Search results

Summary of Contents for SG 300

Reviews:

Related manuals for SG 300

Brands by name

Popular brands

GE SG 300, Installation Manual

Search results

Summary of Contents for SG 300

Reviews:

Related manuals for SG 300

Brands by name

Popular brands