GE UR Series C70 Instruction Manual Download

Page: 557 / 614

GE Multilin

C70 Capacitor Bank Protection and Control System

C-9

APPENDIX C

C.4 GENERIC SUBSTATION EVENT SERVICES: GSSE AND GOOSE

–

Set

CONFIG GSE 1 FUNCTION

to “Enabled”.

–

Set

CONFIG GSE 1 ID

to an appropriate descriptive string (the default value is “GOOSEOut_1”).

–

Set

CONFIG GSE 1 DST MAC

to a multicast address (for example, 01 00 00 12 34 56).

–

Set the

CONFIG GSE 1 VLAN PRIORITY

; the default value of “4” is OK for this example.

–

Set the

CONFIG GSE 1 VLAN ID

value; the default value is “0”, but some switches may require this value to be “1”.

–

Set the

CONFIG GSE 1 ETYPE APPID

value. This setting represents the Ethertype application ID and must match the

configuration on the receiver (the default value is “0”).

–

Set the

CONFIG GSE 1 CONFREV

value. This value changes automatically as described in IEC 61850 part 7-2. For

this example it can be left at its default value.

Configure the data by making the following changes in the

PRODUCT SETUP

ÖØ

COMMUNICATION

ÖØ

IEC 61850 PROTO-

COL

GGIO1 STATUS CONFIGURATION

settings menu:

–

Set

GGIO1 INDICATION 1

to a FlexLogic™ operand used to provide the status of GGIO1.ST.Ind1.stVal (for example,

a contact input, virtual input, a protection element status, etc.).

The C70 must be rebooted (control power removed and re-applied) before these settings take effect.

The following procedure illustrates the reception configuration.

Configure the reception dataset by making the following changes in the

PRODUCT SETUP

ÖØ

COMMUNICATION

ÖØ

IEC

61850 PROTOCOL

GSSE/GOOSE CONFIGURATION

ÖØ

RECEPTION

ÖØ

CONFIGURABLE GOOSE

ÖØ

CONFIG GSE 1 DATASET ITEMS

settings menu:

–

Set

ITEM 1

to “GGIO3.ST.Ind1.q” to indicate quality flags for GGIO3 status indication 1.

–

Set

ITEM 2

to “GGIO3.ST.Ind1.stVal” to indicate the status value for GGIO3 status indication 1.

The reception dataset now contains a set of quality flags, a single point status Boolean value, and a floating point ana-
log value. This matches the transmission dataset configuration above.

Configure the GOOSE service settings by making the following changes in the

INPUTS/OUTPUTS

ÖØ

REMOTE DEVICES

ÖØ

REMOTE DEVICE 1

settings menu:

–

Set

REMOTE DEVICE 1 ID

to match the GOOSE ID string for the transmitting device. Enter “GOOSEOut_1”.

–

Set

REMOTE DEVICE 1 ETYPE APPID

to match the Ethertype application ID from the transmitting device. This is “0” in

the example above.

–

Set the

REMOTE DEVICE 1 DATASET

value. This value represents the dataset number in use. Since we are using

configurable GOOSE 1 in this example, program this value as “GOOSEIn 1”.

Configure the data by making the following changes in the

INPUTS/OUTPUTS

ÖØ

REMOTE INPUTS

ÖØ

REMOTE INPUT 1

settings menu:

–

Set

REMOTE IN 1 DEVICE

to “GOOSEOut_1”.

–

Set

REMOTE IN 1 ITEM

to “Dataset Item 2”. This assigns the value of the GGIO3.ST.Ind1.stVal single point status

item to remote input 1.

Remote input 1 can now be used in FlexLogic™ equations or other settings. The C70 must be rebooted (control power
removed and re-applied) before these settings take effect.

The value of remote input 1 (Boolean on or off) in the receiving device will be determined by the GGIO1.ST.Ind1.stVal value
in the sending device. The above settings will be automatically populated by the EnerVista UR Setup software when a com-
plete SCD file is created by third party substation configurator software.

C.4.5 ETHERNET MAC ADDRESS FOR GSSE/GOOSE

Ethernet capable devices each contain a unique identifying address called a Media Access Control (MAC) address. This
address cannot be changed and is unique for each Ethernet device produced worldwide. The address is six bytes in length
and is usually represented as six hexadecimal values (for example, 00 A0 F4 01 02 03). It is used in all Ethernet frames as
the ‘source’ address of the frame. Each Ethernet frame also contains a

destination

address. The destination address can

be different for each Ethernet frame depending on the intended destination of the frame.