GE VersaMax PLC User Manual Download | Manualshive

Page: 189 / 318

background image

The contact of coil DWELL keeps coil DWELL energized (when contact DO_DWL is
released), and also starts the timer TMRID. When TMRID reaches its preset value of
one-half second, coil REL energizes, interrupting the latched-on condition of coil
DWELL. The contact DWELL interrupts power flow to TMRID, resetting its current
value and de-energizing coil REL. The circuit is then ready for another momentary
activation of contact DO_DWL.

CONST
+00005

DO_DWL

DWELL

DWELL

TMR

PV

TMRID

REL

DWELL

REL

0.15

10.9.3

Timer and Counter Functions Off-Delay Timer

The Off-Delay Timer increments while power flow is off and resets to zero when power
flow is on. Time may be counted in tenths (0.1), hundredths (0.01), or thousandths (0.001)
of a second. Range is 0 to +32,767 time units. The state of this timer is retentive on power
failure; no automatic initialization occurs at power-up.

Enable

Preset Value

OFDT

1.00s

PV

(Q)

Address-3 words

CV

Current Value

When the Off-Delay Timer first receives power flow, it passes power to the right, and the
Current Value (CV) is set to zero. The function uses word 1 [register] as its CV storage
location. The output remains on as long as the function receives power flow. If the
function stops receiving power flow from the left, it continues to pass power to the right,
and the timer starts accumulating time in the Current Value. The Off-Delay Timer does
not pass power flow if the Preset Value is zero or negative.

If multiple occurrences of the same timer with the same reference address are enabled
during a CPU sweep, the Current Values of the timers will be the same.

updated to reflect the elapsed time since the timer was turned off. When the Current Value
(CV) is equal to the Preset Value (PV), the function stops passing power flow to the right
and the timer stops accumulating. When the function receives power flow again, the
current value resets to zero. When this timer is used in a program block that is not called
every sweep, it accumulates time between calls to the program block unless it is reset.
That means it functions like a timer in a program with a much slower sweep than the
timer in the main program block. For program blocks that are inactive for a long time, the
timer should be programmed to allow for this catch-up. For example, if a timer in a
program block is reset and the program block is inactive for four minutes, when the
program block is called, four minutes of time will have accumulated. This time is applied
to the timer when enabled unless the timer is first reset.

Instruction Set Reference

GFK-1503E User Manual 189

For public disclosure

«
...
187
188
189
190
191
...
»

Summary of Contents for VersaMax PLC































































































































































































































































































































Reviews:

No comments

Related manuals for VersaMax PLC

ACS850-04 series

Brand: ABB Pages: 296

Brand: ABB Pages: 320

Brand: ABB Pages: 50

Brand: ABB Pages: 56

Brand: UniKey Pages: 20

Brand: ZEHUS Pages: 28

Brand: Valfonta Pages: 12

Brand: Baby Jogger Pages: 24

Brand: Baby Jogger Pages: 16

city select LUX

Brand: Baby Jogger Pages: 20

CITY ELITE SINGLE

Brand: Baby Jogger Pages: 24

Brand: Baby Jogger Pages: 147

Brand: Banner Pages: 15

Brand: bar Pages: 2

Brand: Bartec Pages: 26

Brand: Baninni Pages: 26

Brand: V2 Pages: 48

Brand: Gascat Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands