GE VersaMax PLC User Manual Download

Page: 278 / 318

Words

Parameter/Description

Low Bit

Units

Range

(A 11)

Minimum Slew Time

Minimum number of seconds for the CV output to move from

0 to full travel of 100% or 32000 CV Counts. It is an inverse

rate limit on how fast the CV output can change.

If positive, CV cannot change more than 32000 CV Counts

times the solution time interval (seconds) divided by Minimum

Slew Time.

For example, if the Sample Period is 2.5 seconds and the

Minimum Slew Time is 500 seconds, CV cannot change more

than 32000 * 2.5 / 500 or 160 CV Counts per PID solution.

The integral term value is adjusted if the CV rate limit is

exceeded.

When Minimum Slew Time is 0, there is no CV rate limit. Set

Minimum Slew Time to 0 while tuning or adjusting PID loop

gains.

Seconds / Full

Travel

0 (none) to 32000 sec

to move full CV travel

(A 12)

Config Word

The low 6 bits of this word are used to modify default PID

settings. The other bits should be set to 0.

Bit 0

: Error Term Mode. When this bit is 0, the error term is SP

- PV. When this bit is 1, the error term is PV - SP. Setting this

bit to 1 modifies the standard PID Error Term from the normal

(SP – PV) to (PV – SP), reversing the sign of the feedback

term. This mode is used for reverse acting controls where the

CV must go down when the PV goes up.

Bit 1

: Output Polarity. When this bit is 0, the CV output is the

output of the PID calculation. When it is set to 1, the CV

output is the negated output of the PID calculation. Setting

this bit to 1 inverts the Output Polarity so that CV is the

negative of the PID output rather than the normal positive

value.

Bit 2

: Derivative action on PV. When this bit is 0, the

derivative action is applied to the error term. When it is set to

1, the derivative action is applied to PV only.

Bit 3

: Deadband action. When the Deadband action bit is 0,

the actual error value is used for the PID calculation. When

the Deadband action bit is 1, deadband action is chosen. If

the error value is within the deadband limits, the error used for

the PID calculation is forced to be zero. If, however, the error

value is outside the deadband limits, the magnitude of the

error used for the PID calculation is reduced by the deadband

limit (|error| = |error – deadband limit|).

278

GFK-1503E

VersaMax PLC User Manual

For public disclosure

Summary of Contents for VersaMax PLC































































































































































































































































































































Search results

Summary of Contents for VersaMax PLC

Reviews:

Related manuals for VersaMax PLC

Brands by name

Popular brands

GE VersaMax PLC, User Manual

Search results

Summary of Contents for VersaMax PLC

Reviews:

Related manuals for VersaMax PLC

Brands by name

Popular brands