background image

4

  D
 GB
  F
  E

96019-05.2012-DGbFEI

1

|

 Safety

1.2  Qualifications required of personnel

1.3  General safety instructions

WARNING!   Inadequately  qualified  personnel  poses  the  risk  of  accidents,  the 

consequence  being  serious  or  fatal  injury.  Work  on  compressors 
must therefore only be performed by personnel with the qualifica

-

tions listed below:

 

•   For  example,  a  refrigeration  technician,  refrigeration  mechatron

-

ics engineer. As well as professions with comparable training, which 
enable personnel to assemble, install, maintain and repair refrigeration 

and air-conditioning systems. Personnel must be capable of assessing 
thework to be carried out and recognising any potential dangers.

WARNING! 

•  

Refrigerating  compressors  are  pressurised  machines  and 

 therefore require particular caution and care in handling.

 

•  

Risk  of  burns!  Depending  on  the  operating  conditions,  surface 

temperatures of over 60 °C on the pressure side or below 0 °C on 
the suction side can be reached.

 

• 

The  maximum  permissible  overpressure  must  not  be  exceeded, 

 

 

  even for testing purposes.

 

1.1  Identification of safety instructions:

DANGER!

  

Indicates a dangerous situation which, if not

 

 

avoided, will cause immediate fatal or serious injury.

 

WARNING!

  

Indicates a dangerous situation which, if not

 

 

avoided, may cause fatal or serious injury.

 

CAUTION!

  

Indicates a dangerous situation which, if not

 

 

avoided, may cause fairly severe or minor injury.

 

ATTENTION!

  

Indicates a situation which, if not

 

 

avoided, may cause property damage.

 

INFO! 

Important information or tips on simplifying work.

 

WARNING!  DANGER OF SUFFOCATION!

 

Never release significant volumes of CO

2

 or the entire contents of  

 

the system into closed rooms!

Summary of Contents for HGX22P CO2 Series





























Reviews: