background image

Ra

ng

Hoo

ds

Vented

GEAppliances.ca

350A4502P760   07-14   ATS

Safety Information

   .  .  .  .  .  .  .  .  .  .  . 2

Operating/Care and  

Cleaning Instructions

Charcoal Filters   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 

Grease Filters   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3 

Hood Lights  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 

Painted Surfaces   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4 

Stainless Steel Surfaces    .  .  .  .  .  .  .  .  .  . 4 

Vent Controls   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3

Installation Instructions

   .  .5–12

Troubleshooting Tips

   .  .  .  .  .  .  . 14 

Consumer Support

 

Consumer Support   .  .  .  .  .  .  .  .  .  .  .  .  .  . 18 

Product Registration    .  .  .  .  .  .  .  .  .  .  .  . 15 

Warranty   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 17

JVE330

Owner’s Manual 

and Installation 

Instructions

Write the model and serial  

numbers here:
Model # ________________
Serial # _________________

Find these numbers on a label on 

the back wall of the hood .

Printed in China

Summary of Contents for JVE330



















Reviews: