background image

14

350A4502P760

Before you call for service…

Troubleshooting Tips  

Save time and money! Review the following chart first  

and you may not need to call for service.

Problem 

Possible Causes 

What To Do

Fan does not operate

 

A fuse may be blown or a 

 

•  Replace fuse or reset circuit breaker.

 

when the switch is on

 

circuit breaker may be tripped.   

Fan fails to circulate air

 

Excessively soiled filter.

 

•  Wash and replace the filters. See the Reusable

  

or moves air more slowly

  

 

Metal Grease Filters

 section .

than normal

 

 

•  Replace the filter if it is too soiled to clean. If it 

 

 

 

  is not soiled, or if replacing the filter does not  

 

 

  solve the problem, call for service .

 

 

• 

Sufficient makeup (replacement) air is required for  

 

 

  exhausting appliances to operate to rating . Check with  

 

 

  local building codes, which may require or strongly advise 

 

 

  the use of makeup air . Visit 

GEAppliances.ca

 for available  

 

 

  makeup air solutions .

Fan continually cycles

 

The motor is probably 

 

•  Replace the filter if it is soiled. If it is not soiled, 

 

off and on

 

overheating and turning itself 

    or if replacing the filter does not solve the problem, 

 

off. This can be harmful to 

 

  call for service . 

 

the motor. Filter may be 

 

 

excessively soiled.

Compact Fluorescent

 

This is normal for Compact

 

•  Allow lamp to run for several minutes.  If this warm up

 

Lamp appears dim  

 

Fluorescent Lamps especially 

 

  time does not solve the problem replace the lamp . 

on start up 

on first installation.

Compact Fluorescent 

 

This is normal for Compact

 

•  Allow lamp to run for several minutes.

 

Lamp briefly  

Fluorescent Lamps

  

If this warm up time does not solve the problem 

flickers on start up 

 

especially on first installation. 

    replace the lamp .

After replacing one  

The replacement lamp may  

•  Use a GE 15W GU24 base lamp with a 2700K rating.

 

lamp, the new lamp 

have a different color  

 

GE Service Part number WB08X10064.

 

appears to be a  

temperature rating : i.e. is

 

different color 

3000K instead of 2700K.

 

The replacement lamp may 

•  Use a GE 15W GU24 base lamp with a GE Service Part

 

 

be from a different 

 

number WB08X10064.

 

 

manufacturer.

Summary of Contents for JVE330



















Reviews: