49-85220-1
31
Problem
Possible Cause
What To Do
Oven light does not
work
Light bulb is loose or defective.
Tighten or replace bulb. See the Maintenance section for
instructions on how to replace the bulb.
Oven will not self-clean
The temperature is too high to set
a self-clean operation.
Allow the oven to cool.
Oven controls improperly set.
See the Cleaning the Oven section.
Excessive smoking
during clean cycle
Excessive soil or grease.
Press the
Cancel/Off
pad. Allow the oven to cool below
the unlocking temperature. Wipe the excess soil and
reset the clean cycle.
Oven not clean after a
clean cycle
Oven controls improperly set.
See the Cleaning the Oven section.
Oven was heavily soiled.
Clean up heavy spillovers before starting the clean cycle.
Heavily soiled ovens may need to self-clean again or for
a longer period of time.
Strong “burning” or
“oily” odor emitting
from the vent
This is normal in a new oven and
will disappear in time.
To speed the process, set a self-clean cycle for a
PLQLPXPRIKRXUV6HHWKH&OHDQLQJWKH2YHQ VHFWLRQ
This is temporary.
Excessive smoking
during broiling
Food too close to burner element.
/RZHUWKHUDFNSRVLWLRQRIWKHIRRG
Oven latch will not open.
The temperature inside the
oven has not dropped below the
unlocking temperature.
Press the
Cancel/Off
pad. Allow the oven to cool below
the unlocking temperature.
"LOCK DOOR" flashes
in the display
The self-clean or steam-clean cycle
has been selected but the door is
not locked.
/RFNWKHRYHQGRRU
“F— and a number
or letter” flash in the
display
You have a function error code.
Press the
Cancel/Off
pad. Allow the oven to cool for one
hour. Put the oven back into operation. If the function code
UHSHDWVGLVFRQQHFWDOOSRZHUWRWKHRYHQIRUDWOHDVW
seconds and then reconnect power. If the function error code
repeats again, call for service.
Clock flashes due to a
power outage
Power outage or surge
Reset the clock. If the oven was in use, you must reset
it by pressing the
Cancel/Off
pad, setting the clock and
resetting any cooking function.
Lock Controls or
Control Lockout feature
is activated
If
LOC ON
appears in the display, the range control is
locked. Turn this feature off to use the range. See the
Oven Controls section.
Surface Burners do not
light
Plug on range is not completely
inserted in the electrical outlet.
Make sure electrical plug is plugged into a live, properly
grounded outlet.
Gas supply not connected or
turned on.
See the Installation Instructions that came with your
range.
A fuse in your home may be blown
or the circuit breaker tripped.
Replace the fuse or reset the circuit breaker.
Burner parts not replaced correctly.
See the Care and Cleaning section.
Burner slots near the electrode, or
the round lighter port on the oval
burner, may be clogged.
Remove the burners and clean them. Check the
electrode area for burned-on food or grease. See the
Care and Cleaning section.
Food residue on electrode
/LJKWO\SROLVKIODWWLSRIHOHFWURGHZLWKQDLOILOHRU
sandpaper until shiny.
Troubleshooting tips ... Before you call for service
TR
OUBLESHOO
TING TIPS
Summary of Contents for RGB780DEH1WW
