background image

Gefen Inc. warrants the equipment it manufactures to be free 
from defects in material and workmanship.

If equipment fails because of such defects and Gefen Inc. is 
notifi ed within two (2) year from the date of shipment, Gefen Inc. 
will, at its option, repair or replace the equipment, provided that 
the equipment has not been subjected to mechanical, electrical, 
or other abuse or modifi cations. The two year warranty is only 
valid on new products purchased as of January 2007. All products 
purchased before this date still retain their 1 year warranty.

Equipment that fails under conditions other than those covered 
will be repaired at the current price of parts and labor in effect 
at the of repair. Such repairs are warranted for ninety (90) days 
from the day of reshipment to the Buyer.

This warranty is in lieu of all other warranties expressed or 
implied, including without limitation, any implied warranty or 
merchantability or fi tness for any particular purpose, all of which 
are expressly disclaimed. Please note that:

1.   Proof of sale may be required in order to claim warranty. 

2.  Customers outside the US are responsible for shipping 
charges to and from Gefen.

3.  Copper cables are limited to a 30 day warranty and cables 
must be in their original condition. 

For the latest warranty coverage information, please visit 
Gefen’s Warranty page at http://www.gefen.com/kvm/aboutus/
warranty.jsp

PRODUCT REGISTRATION

Please register your product online by visiting Gefen at: 

http://www.gefen.com/kvm/Registry/Registration.jsp

The information in this manual has been carefully checked and 
is believed to be accurate. However, Gefen Inc. assumes no 
responsibility for any inaccuracies that may be contained in this 
manual. In no event will Gefen Inc., be liable for direct, indirect, 
special, incidental, or consequential damages resulting from any 
defect or omission in this manual, even if advised of the possibility 
of such damages. The technical information contained herein 
regarding the DVI Detective Plus features and specifi cations is 
subject to change without notice.

WARRANTY

12

Summary of Contents for DVI Detective Plus



















Reviews: