manualshive.com logo in svg

Gemalto CINTERION BGS2T, At Command Set

The Gemalto CINTERION BGS2T is a cutting-edge GSM/GPRS wireless module. Our comprehensive user manual, complete with an extensive AT Command Set, is available for free download on our website. Discover the full potential of this product by accessing the manual at 88.208.23.73:8080.

Share
Download
background image

BGS2T AT Command Set  

5.1 AT+CPIN

BGS2T_ATC_V01.301

Page 112 of 554

1/31/12

 

c

Notes

•

Successful PIN authentication only confirms that the entered PIN was recognized and correct. The output of 
the result code OK does not necessarily imply that the mobile is registered to the desired network.
Typical example: PIN was entered and accepted with OK, but the ME fails to register to the network. This may 
be due to missing network coverage, denied network access with currently used SIM card, no valid roaming 
agreement between home network and currently available operators etc.
BGS2T offers various options to verify the present status of network registration: For example, the 

AT+COPS

 

command indicates the currently used network. With 

AT+CREG

 you can also check the current status and acti-

vate an unsolicited result code which appears whenever the status of the network registration changes (e.g. 
when the ME is powered up, or when the network cell changes).

•

<pin>

 and 

<new pin>

 can also be entered in quotation marks (e.g. "1234").

•

To check the number of remaining attempts to enter the passwords use the 

AT^SPIC

 command.

•

See 

AT+CPWD

 and 

AT^SPWD

 for information on passwords.

•

See 

AT+CLCK

 and 

AT^SLCK

 for information on lock types.

5.1.1

What to do if PIN or password authentication fails?

PIN1 / PUK1:
After three failures to enter PIN 1, the SIM card is blocked (except for emergency calls). +CME ERROR: 12 will 
prompt the client to unblock the SIM card by entering the associated PUK (= PIN Unblocking Key / Personal 
Unblocking Key). After ten failed attempts to enter the PUK, the SIM card will be invalidated and no longer oper-
able. In such a case, the card needs to be replaced. PIN1 consists of 4 to 8 digits, PUK1 is an 8-digit code only.
To unblock a disabled PIN1 you have two options: 

•

You can enter 

AT+CPIN

=PUK1,new PIN1.

•

You can use the 

ATD

 command followed by the GSM code **05*PUK*newPIN*newPIN#;.

PIN2 / PUK2: 
PIN2 prevents unauthorized access to the features listed in 

AT+CPIN2

. The handling of PIN2 varies with the pro-

vider. PIN2 may either be a specific code supplied along with an associated PUK2, or a default code such as 
0000. In either case, the client is advised to replace it with an individual code. Incorrect input of PUK2 will per-
manently block the additional features subject to PIN2 authentification, but usually has no effect on PIN1. PIN2 
consists of 4 digits, PUK2 is an 8-digit code only.
To unblock a disabled PIN2 you have two options: 

•

You can enter 

AT+CPIN2

=PUK2,new PIN2.

•

You can use the 

ATD

 command followed by the GSM code **052*PUK2*newPIN2*newPIN2#;.

Phone lock: 
If the mobile was locked to a specific SIM card (= "PS" lock or phone lock), the PUK that came with the SIM card 
cannot be used to remove the lock. After three failed attempts to enter the correct password, ME rCPIN: 
PH-SIM PUK (= response to read command 

AT+CPIN

?), i.e. it is now waiting for the Master Phone Code. This 

is an 8-digit device code associated to the IMEI number of the mobile which can only by obtained from the man-
ufacturer or provider. When needed, contact Cinterion Wireless Modules GmbH and request the Master Phone 
Code of the specific module.
There are two ways to enter the Master Phone code: 

•

You can enter 

AT+CPIN

=Master Phone Code

•

You can use the 

ATD

 command followed by the GSM code *#0003*Master Phone Code#;.

Usually, the Master Phone Code will be supplied by mail or e-mail. If the received number is enclosed in the *# 
codes typically used for the 

ATD

 option, it is important to crop the preceding *#0003* characters and the 

appended #. 
Example: You may be given the string *#0003*12345678#. When prompted for the PH-SIM PUK simply enter 
12345678.
If incorrectly input, the Master Phone Code is governed by a specific timing algorithm: (n-1)*256 seconds (see 
table below). The timing should be considered by system integrators when designing an individual MMI. 

Confidential / Released

Summary of Contents for CINTERION BGS2T











































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CINTERION BGS2T

GRAVITY iWL255 User Quick Reference Manual preview
iWL255
Brand: GRAVITY Pages: 2
Inepro Back Office Suite Technical Manual preview
Back Office Suite
Brand: Inepro Pages: 248
Element CA250W User Manual preview
CA250W
Brand: Element Pages: 33
FlexiForce GSM-02 Manual preview
GSM-02
Brand: FlexiForce Pages: 52
Gemalto MagIC3 C-series Maintenance Manual preview
MagIC3 C-series
Brand: Gemalto Pages: 35
Zte AC2792 User Manual preview
AC2792
Brand: Zte Pages: 16
POSIFLEX KS - 2010 User Manual preview
KS - 2010
Brand: POSIFLEX Pages: 19
Hisense HK716 Series System Integration Manual preview
HK716 Series
Brand: Hisense Pages: 22
YASKAWA 62E-MDC0 Manual preview
62E-MDC0
Brand: YASKAWA Pages: 48
UIC nPOS Junior Quick Manual preview
nPOS Junior
Brand: UIC Pages: 4
PairGain HiGain HDU-217 Manual preview
HiGain HDU-217
Brand: PairGain Pages: 28
Fametech POStation 7000 Series Service Manual preview
POStation 7000 Series
Brand: Fametech Pages: 16
XMODUS XM1640S Operating Instructions preview
XM1640S
Brand: XMODUS Pages: 2
Jepower JP762A User Manual preview
JP762A
Brand: Jepower Pages: 9
FEC WITOUCH CORE 6E User Manual preview
WITOUCH CORE 6E
Brand: FEC Pages: 28
Velleman HAA920 User Manual preview
HAA920
Brand: Velleman Pages: 83
Panasonic TY-FB8TA Operating Instructions Manual preview
TY-FB8TA
Brand: Panasonic Pages: 48
Panasonic TY-FB30DHD3D Operating Instructions Manual preview
TY-FB30DHD3D
Brand: Panasonic Pages: 76

Brands by name

Popular brands

Load more brands